Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSMINI2013COOPER COUNTRYMAN, STANDARD TRANSREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 4291 (GENERAL ELECTRICAL SYSTEM - REPAIR - F32)CONTROL UNITS, MODULES, SENSORS, AERIALS61 35... OVERVIEW, RAIN SENSOR (ADDITIONAL WORK WHEN REPLACING THE WINDSCREEN/SENSOR REPLACEMENT)
2013 Mini Cooper Countryman, Standard Trans
61 35... Overview, rain sensor (additional work when replacing the windscreen/sensor replacement)
2013 Mini Cooper Countryman, Standard TransSECTION 61 35... Overview, rain sensor (additional work when replacing the windscreen/sensor replacement)
WARNING: This page does not describe the selected car, but rather 12 other vehicles, including the 2016 BMW 435i xDrive, 2016 BMW 435i, 2016 BMW 428i xDrive, 2016 BMW 428i, and 2015 BMW 435i xDrive. However, it is still accessible from the selected car via links, so may be relevant.
- 1-Series: E8x
- 3-Series: E9x
- 5-Series: E6x
- 6-Series: E6x
- X1: E84
- Z4: E89
| Sensor type/Sensor shape | With windscreen replacement sensor required | When replacing the sensor/Programming/encoding necessary | When replacing the sensor/Initialization required | Connecting the diagnosis system required |
|---|---|---|---|---|
| Condensation sensor square 30 x 20 mm |
Yes | No | No | No |
- 5-Series: E6x
- 6-Series: E6x
- 7-Series: E6x
| Sensor type/Sensor shape | With windscreen replacement sensor required | When replacing the sensor Programming/encoding necessary | When replacing substitute visuals Programming/encoding necessary | When replacing the sensor/substitute visuals Initialization required | Connecting the diagnosis system required |
|---|---|---|---|---|---|
| all types square 60 x 40 mm |
No | Yes | - | Yes | Yes |
| RLS approximately Ø 50 mm |
No (new substitute visuals required) |
- | No | Yes | Yes |
- X5: E70
- X6: E7x
| Sensor type/Sensor shape | With windscreen replacement sensor required | When replacing the sensor Programming/encoding necessary | When replacing substitute visuals Programming/encoding necessary | When replacing the sensor/substitute visuals Initialization required | Connecting the diagnosis system required |
|---|---|---|---|---|---|
| RLPSS (Rain, light and precipitation solar sensor) (Designation is located on the back of the sensor) approximately Ø 50 mm |
Yes | Yes | - | Yes | Yes |
| RLS (vehicle with no HUD) (Designation is located on the back of the sensor) approximately Ø 50 mm (new substitute visuals required) |
No | - | No | Yes | Yes |
| RLSS (vehicle with HUD) (Designation is located on the back of the sensor) approximately Ø 50 mm |
Yes | Yes | - | Yes | Yes |
- 1-Series: E8x
- 3-Series: E9x
- X1: E84
- X3: E83
- Z4: E89
| Sensor type/Sensor shape | With windscreen replacement sensor required | When replacing the sensor Programming/encoding necessary | When replacing the sensor Initialization required | Connecting the diagnosis system required |
|---|---|---|---|---|
| all types square 60 x 40 mm |
No | Yes | Yes | Yes |
- 5-Series: F1x
- 5-Series GT: F07
- 6-Series: F06, F1x
- 7-Series: F0x
- X3: F25
- X4: F26
| Sensor type/Sensor shape | With windscreen replacement sensor required | When replacing the sensor Programming/encoding necessary | When replacing substitute visuals Programming/encoding necessary | When replacing the sensor/substitute visuals Initialization required | Connecting the diagnosis system required |
|---|---|---|---|---|---|
| all types approximately Ø 35 mm |
No | No | - | Yes | Yes |
| all types approximately Ø 50 mm |
Yes | Yes | - | Yes | Yes |
| Only for F25: RLS approximately Ø 50 mm |
No (new substitute visuals required) |
- | No | Yes | Yes |
- X5: F15, F85
- X6: F16, F86
| Sensor type/Sensor shape | With windscreen replacement sensor required | When replacing the sensor Programming/encoding necessary | When replacing the sensor Initialization required | Connecting the diagnosis system required |
|---|---|---|---|---|
| all types approximately Ø 35 mm |
No | No | No | No |
- 1-Series: F2x
- 2-Series: F2x
- 3-Series: F3x, F8x
- 3-Series GT: F34
- 4-Series: F3x, F8x
| Sensor type/Sensor shape | With windscreen replacement sensor required | When replacing the sensor Programming/encoding necessary | When replacing the sensor Initialization required | Connecting the diagnosis system required |
|---|---|---|---|---|
| all up to 03/2014 except SBS (01) (Designation is located on the back of the sensor) approximately Ø 35 mm |
No | No | Yes | Yes |
| SBS (01) (Designation is located on the back of the sensor) approximately Ø 35 mm |
No | No | No | No |
| All as from 03/20 14 approximately Ø 35 mm |
No | No | No | No |
BMW i:
| Sensor type/Sensor shape | With windscreen replacement sensor required | When replacing the sensor Programming/encoding necessary | When replacing the sensor Initialization required | Connecting the diagnosis system required |
|---|---|---|---|---|
| all types approximately Ø 35 mm |
No | No | No | No |
MINI (all):
| Sensor type/Sensor shape | With windscreen replacement sensor required | When replacing the sensor Programming/encoding necessary | When replacing the sensor Initialization required | Connecting the diagnosis system required |
|---|---|---|---|---|
| all types square 60 x 40 mm |
No | Yes | Yes | Yes |
| all types approximately Ø 35 mm |
No | No | No | No |
Roll s-Royce (all):
| Sensor type/Sensor shape | With windscreen replacement sensor required | When replacing the sensor Programming/encoding necessary | When replacing the sensor Initialization required | Connecting the diagnosis system required |
|---|---|---|---|---|
| all types square 60 x 40 mm |
No | Yes | Yes | Yes |
| all types approximately Ø 35 mm |
No | No | Yes | Yes |
| all types approximately Ø 50 mm |
Yes | Yes | Yes | Yes |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.