Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSMINI2013COOPER COUNTRYMAN, STANDARD TRANSREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 3077 (ENGINE - REPAIR - E90)
2013 Mini Cooper Countryman, Standard Trans
Section 3077 (Engine - Repair - E90)
2013 Mini Cooper Countryman, Standard TransSECTION Section 3077 (Engine - Repair - E90)
WARNING: This page is about a different car, the 2011 BMW M3, 2010 BMW M3, 2009 BMW M3, and 2008 BMW M3. However, it is still accessible from the selected car via links, so may be relevant.
- Engine, General
- 11 00 039 Checking compression of all cylinders (S65)
- 00 Danger of poisoning if oil is ingested/absorbed through the skin
- Engine identification
- 11 00 091 Installing replacement engine (S65)
- Mounting engine on assembly stand (S65)
- 11 00... Overview of consumables (Electronic Parts Catalogue)
- 11 00 050 Removing and installing engine (S65)
- 00 Risk of injury if oil comes into contact with eyes and skin
- 00 Safety information for working on vehicles with automatic engine start-stop function (MSA)
- 00 Safety instructions for handling oil
- 11 00 670 Securing engine in installation position (S65)
- 11 00... Service - engine oil (S65)
- Cylinder Head And Cylinder Head Cover
- 11 12 729 Checking cylinder head for watertightness (S65)
- 11 12 105 Removing and installing left cylinder head (S65)
- 11 12 106 Removing and installing right cylinder head (S65)
- 11 12 005 Removing and installing/sealing left cylinder head cover (S65)
- 11 12 006 Removing and installing/sealing right cylinder head cover (S65)
- 11 12 112 Replacing both cylinder head gaskets (S65)
- Oil Sump
- Housing Cover
- Crankshaft With Bearing
- Flywheel
- Vibration Damper
- Connecting Rod With Bearing
- Piston With Rings And Pin
- V-Ribbed Belt With Tension Deflection Element
- Camshaft
- 11 31 575 Adjusting camshaft timing (S65)
- 11 31 072 Checking camshaft timing (S65)
- 11 31 032 Removing and installing or replacing left inlet camshafts (S65)
- 11 31 036 Removing and installing/replacing left exhaust camshaft (S65)
- 11 31 094 Removing and installing/replacing left hydraulic chain tensioner (S65)
- 11 31 038 Removing and installing/replacing right exhaust camshaft (S65)
- 11 31 095 Removing and installing/replacing right hydraulic chain tensioner (S65)
- 11 31 034 Removing and installing/replacing right inlet camshaft (S65)
- 11 31 051 Replacing both timing chains (S65)
- Rocker Arm With Bearing Mount
- Valves With Springs
- Variable Camshaft Timing
- 11 36 144 Removing and installing/replacing left exhaust VANOS gear (S65)
- 11 36 142 Removing and installing/replacing left inlet VANOS gear (S65)
- 11 41 050 Removing and installing/replacing oil suction pump (S65)
- 11 36 150 Removing and installing/replacing right exhaust VANOS gear (S65)
- 11 36 148 Removing and installing/replacing right inlet VANOS gear (S65)
- 11 36 715 Removing and installing/replacing solenoid valves on left VANOS adjustment unit (S65)
- 11 36 720 Removing and installing/replacing solenoid valves on right VANOS adjustment unit (S65)
- Oil Pump With Filter And Drive
- Oil Filter And Lines
- Water Pump With Drive
- Thermostat And Connections
- Intake Manifold
- Air Pump, Lines And Control Valves
- Emission Control, Oxygen Sensor
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.