Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSMINI2013COOPER COUNTRYMAN, STANDARD TRANSREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 2450 (ENGINE - REPAIR (N63))
2013 Mini Cooper Countryman, Standard Trans
Section 2450 (Engine - Repair (N63))
2013 Mini Cooper Countryman, Standard TransSECTION Section 2450 (Engine - Repair (N63))
WARNING: This page does not describe the selected car, but rather 7 other vehicles, including the 2014 BMW X6, 2013 BMW X6, 2012 BMW X6, 2011 BMW X6, and 2010 BMW X6. However, it is still accessible from the selected car via links, so may be relevant.
- Engine General
- 00 Danger of poisoning if oil is ingested/absorbed through the skin
- 00 Risk of injury if oil comes into contact with eyes and skin
- 00 Safety instructions for handling oil
- 00 Safety information for working on vehicles with automatic engine start-stop function (MSA)
- Removing engine cover (N63)
- 11 00... Overview of consumables (Electronic Parts Catalogue - EPC)
- 11 00... Service - engine oil (N63)
- 11 00 050 Removing and installing/replacing engine (N63)
- 11 00 598 Removing and installing engine on front axle E70 E71 (N63/S63)
- 11 00 670 Securing engine in installation position (N63)
- Engine identification
- Cylinder Head And Cylinder Head Cover
- 11 12 005 Removing and installing/sealing left cylinder head cover (N63)
- 11 12 006 Removing and installing/sealing right cylinder head cover (N63)
- 11 12 105 Removing and installing left cylinder head (N63)
- 11 12 106 Removing and installing right cylinder head (N63)
- 11 12 112 Replacing both cylinder head gaskets (N63)
- 11 12 719 Grinding cylinder head sealing surface (N63)
- 11 12 729 Checking cylinder head for watertightness (N63)
- Oil Sump
- Housing Cover
- 11 14 080 Removing and installing timing case cover, top left (N63)
- 11 14 085 Removing and installing timing case cover, top right (N63)
- 11 14 110 Removing and installing lower timing case cover (N63)
- 11 14 141 Replacing radial shaft seal in lower timing case cover (N63)
- 11 14 151 Replacing crankshaft radial seal on transmission side (N63)
- 11 14 250 Removing and installing/sealing rear coolant end cover (N63)
- Crankshaft With Bearing
- Flywheel
- Vibration Damper
- Connecting Rod With Bearing
- Piston With Rings And Pin
- V-Ribbed Belt With TENSIONER
- Camshaft
- 11 31 032 Removing and installing/replacing left inlet camshaft (N63)
- 11 31 034 Removing and installing/replacing right inlet camshaft (N63)
- 11 31 036 Removing and installing/replacing left exhaust camshaft (N63)
- 11 31 038 Removing and installing/replacing right exhaust camshaft (N63)
- 11 31 052 Replacing both timing chains (N63)
- 11 31 070 Checking camshaft timing on left side (N63)
- 11 31 071 Checking camshaft timing on right side (N63)
- 11 31 094 Removing hydraulic chain tensioner for timing chains on left side (N63)
- 11 31 095 Removing hydraulic chain tensioner for timing chains on right side (N63)
- 11 31 573 Adjusting camshaft timing on left side (N63)
- 11 31 574 Adjusting camshaft timing on right side (N63)
- Rocker Arm With Bearing Mount
- Valves With Springs
- Variable Camshaft Timing
- 11 36 047 Removing and installing/replacing inlet and exhaust adjustment units on left side (N63)
- 11 36 048 Removing and installing/replacing inlet and exhaust adjustment units on right side (N63)
- 11 36 715 Removing and installing/replacing both solenoid valves on left side (N63)
- 11 36 720 Removing and installing/replacing both solenoid valves on right side (N63)
- Oil Supply
- Oil Pump With Filter And Drive
- Oil Filter And Lines
- Water Pump With Drive
- Thermostat And Connector
- Intake Manifold
- 11 61 065 Removing and installing/replacing left intake manifold (N63)
- 11 61 068 Removing and installing/replacing right intake manifold (N63)
- 11 61 730 Check BMW diagnosis system for excess pressure and vacuum (N63)
- Notes
- Necessary preliminary work
- Pressure measurement
- Vacuum pressure measurement
- Calibration for vacuum pressure measurement
- Connections on EPPC
- Vacuum activation, cylinders 1-4
- Vacuum activation, cylinders 5-8
- Exhaust turbocharger, cylinders 1-4
- Exhaust turbocharger, cylinders 5-8
- Check wastegate valve with vacuum
- Supercharger
- 11 65 Connection diagram, vacuum activation (N63)
- 11 65 010 Removing and installing/replacing pressure accumulator (N63)
- 11 65 025 Removing and installing/replacing exhaust turbocharger, right, cylinders 1-4 (N63)
- 11 65 030 Removing and installing/replacing exhaust turbocharger, left, cylinders 5-8 (N63)
- 11 65 165 Removing and installing/replacing blow-off valve (N63)
- 11 65 180 Removing and installing/replacing heat shield at top (N63)
- 11 65 185 Removing and installing/replacing heat shield at bottom (N63)
- 11 65 712 Removing and installing/replacing electric changeover valve on exhaust turbocharger, left (N63)
- 11 65 714 Removing and installing/replacing electric changeover valve on exhaust turbocharger, right (N63)
- Vacuum Pump
- Turbocharger Valve For Exhaust Gas
- Emission Control Oxygen Sensor
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.