Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSMINI2013COOPER COUNTRYMAN, STANDARD TRANSREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 2158 (FUEL SYSTEM - TIGHTENING TORQUES)SENSOR FOR CONTROL UNIT13 62 SENDERS FOR CONTROL UNIT
2013 Mini Cooper Countryman, Standard Trans
13 62 Senders for Control Unit
2013 Mini Cooper Countryman, Standard TransSECTION 13 62 Senders for Control Unit
WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2010 BMW 535xi, 2010 BMW 535i, 2009 BMW 535xi, 2009 BMW 535i, and 2008 BMW 535xi. However, it is still accessible from the selected car via links, so may be relevant.
SENDERS FOR CONTROL UNIT - TIGHTENING TORQUES SPECIFICATION
| Type | Thread | Tightening specification | Measure | |
|---|---|---|---|---|
| 1AZ Temperature time switch | M21 / M51 | 18 Nm | ||
| 2AZ Temperature sensor, water | M60/1 / M60/2 / M21 / M51 | 18 Nm | ||
| all others | 13 Nm | |||
| 3AZ Temperature switch | All | 28 Nm | ||
| 4AZ Temperature sensor, air | All | 13 Nm | ||
| 5AZ Charge-air pressure sensor to bracket | M51 / M41 | 4 Nm | ||
| Charge-air pressure sensor to intake manifold | M47 | 5 Nm | ||
| 6AZ Dual temperature sensor (4-pin plug connection) | M41 / M43 / M44 / S50 / S52 / M52/ M57 / M67 / M62 / M73 | 13 Nm | ||
| 7AZ Air-mass sensor on lower section of intake filter housing | M51 | 3.5 Nm | ||
| Air-mass flow sensor to cylinder head cover | M47 / M47TU / M57 / M57TU / M57T2 | 4.5 Nm | ||
| 8AZ Pulse generator, camshaft to cylinder head cover | M57 | 4.5 Nm | ||
| M47TU / M57TU | 3.5 Nm | |||
| M57T2 | 2.3 Nm | |||
| 9AZ Intake neck on air-mass flow sensor | M47 | 9 Nm |
SENDERS FOR CONTROL UNIT - TIGHTENING TORQUES SPECIFICATION
| Type | Thread | Tightening specification | Measure | |
|---|---|---|---|---|
| 1AZ Coolant temperature sensor | N54 | M12 x 1.5 | 13.5 Nm | |
| 2AZ Intake pressure sensor | N54 | K50 x 18 | 3.5 Nm | |
| 3AZ Camshaft sensor to cylinder head | N54 | M6 x 16 | 8 Nm | |
| 4AZ Crankshaft sensor to crankcase | N54 | M6 x 16 | 8 Nm | |
| 5AZ Knock sensor to crankcase | N54 | M8 x 30 | 21.5 Nm |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.