SDVOSB Certified

Safety Warning

DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.

SYS.OK|MANUAL.DB● LIVE

HOMESERVICE MANUALSMINI2013COOPER COUNTRYMAN, STANDARD TRANSREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1553 (TRAILERS - REPAIR)10 LOADING PLATFORM86 10 ... REPLACING DRAWBAR MEMBERS, LEFT AND RIGHT

2013 Mini Cooper Countryman, Standard Trans

86 10 ... Replacing Drawbar Members, Left And Right

2013 Mini Cooper Countryman, Standard TransSECTION 86 10 ... Replacing Drawbar Members, Left And Right

WARNING: This page is about a different car, the 2010 BMW X5, 2009 BMW X5, 2008 BMW X5, and 2007 BMW X5. However, it is still accessible from the selected car via links, so may be relevant.

NOTE: Disassembly of overrunning equipment,
refer to 86 10 ... DISASSEMBLY OF OVERRUNNING EQUIPMENT .
Remove complete brake pull rod.
Removal of position light cable,
refer to 86 10 ... REPLACING LICENSE PLATE LIGHT .

Release screws (1) on cross-member (2). Pull out crossmember (2) towards rear.

Installation:

Tightening Torque, refer to 86 10 PLATFORM .

Fig 1: Identifying Screws On Cross-Member

G04766422

Courtesy of BMW OF NORTH AMERICA, INC.

Release countersunk head screws (1) and remove.

Installation:

Tightening Torque, refer to 86 10 PLATFORM .

Fig 2: Identifying Countersunk Head Screws

G04766423

Courtesy of BMW OF NORTH AMERICA, INC.

Remove cable holder (1) and remove wiring harness (2) from drawbar member (3).

Fig 3: Identifying Cable Holder, Wiring Harness And Drawbar Member

G04766424

Courtesy of BMW OF NORTH AMERICA, INC.

Remove cable (1) from position light housing (2). Pull out cable (1) through drawbar member aperture (3).

Fig 4: Identifying Cable And Drawbar Member Aperture

G04766401

Courtesy of BMW OF NORTH AMERICA, INC.

Release all screws on cross-member (1) and remove crossmember (1).

If necessary, release screws on mounting brackets (2) and remove cross-members (3).

Installation:

Use new self-locking nuts.

Tightening Torque, refer to 86 10 PLATFORM .

Fig 5: Identifying Cross-Member, Mounting Brackets And Cross-Members

G04766426

Courtesy of BMW OF NORTH AMERICA, INC.

Unscrew bolt (1). Grip nut from rear through assembly hole (2) in cross-member.

Installation:

Use new self-locking nuts.

Tightening Torque, refer to 86 10 PLATFORM .

Fig 6: Identifying Assembly Hole In Cross-Member

G04766427

Courtesy of BMW OF NORTH AMERICA, INC.

Tilt drawbar member (1) down in direction of arrow A and pull out towards rear in direction of arrow B.

Fig 7: Tilting Drawbar Member

G04766428

Courtesy of BMW OF NORTH AMERICA, INC.

RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready Tools Free Quote Check Quote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

• You smell fuel, burning insulation, or see smoke.
• Brakes feel soft, pull hard to one side, or make grinding noises.
• The engine overheats, stalls repeatedly, or misfires under load.
• You are missing required tools, torque specs, or safe lifting equipment.
• You are not confident in the next step or safety outcome.