Autolock and Auto-Unlock Programming

Autolock and Auto-Unlock Programming

Autolock Programming Using the Keyless Entry Keypad

1. Close all doors and windows.

2. Confirm that the ignition key is OFF.

3. Enter the 5-digit permanent entry code into the keyless entry keypad.

4. Within 5 seconds of entering the code, press and hold the 3/4 button on the keyless entry keypad.

5. Within 5 seconds of Step 3, and while holding the 3/4 button, press the 7/8 button on the keyless entry keypad and release it.

6. NOTE: If the autolock is disabled, the horn chirps once. If the autolock feature is enabled, the horn chirps once shortly and then sounds a second time with a longer sound of the horn once the above sequence is completed.

Within 5 seconds of Step 3, release the 3/4 button on the keyless entry keypad.

Autolock Programming Using the Ignition Lock Cylinder

1. Close all doors and windows.

2. Confirm that the ignition key is OFF.

3. NOTE: Steps 5 through 9 must be carried out within 30 seconds.

Turn the ignition key from OFF to RUN.

4. Press the door lock control switch UNLOCK button 3 times.

5. Turn the ignition key from RUN to OFF.

6. Press the door lock control switch UNLOCK button 3 times.

7. Turn the ignition key from OFF to RUN.

8. Verify the horn chirps. This indicates the enable/disable mode and now is ready to accept program changes.

9. Press the door lock control switch UNLOCK button then the LOCK button 1 time to command the module to toggle the autolock/relock feature.

10. Verify that the horn chirps. There should be 1 chirp indicating that autolock/relock feature has been disabled. If 1 chirp is heard, followed by a longer sound of the horn, the autolock/relock feature has just been enabled.

11. Turn the key to the OFF position or wait 2 minutes to exit the enable/disable mode.

12. Verify that the horn chirps once to indicate that a feature has been changed and that autolock/relock has been toggled.

Auto-Unlock Programming Using the Keyless Entry Keypad

1. Close all doors and windows.

2. Confirm that the ignition key is OFF.

3. Enter the 5-digit permanent entry code into the keyless entry keypad.

4. Within 5 seconds of entering the code, press and hold the 3/4 button on the keyless entry keypad.

5. Within 5 seconds of Step 3, and while holding the 3/4 button, press the 7/8 button twice on the keyless entry keypad and release it.

6. NOTE: If the auto-unlock is disabled, the horn chirps once. If the auto-unlock feature is enabled, the horn chirps twice.

Within 5 seconds of Step 3, release the 3/4 button on the keyless entry keypad.

Auto-Unlock Programming Using the Ignition Lock Cylinder

1. Close all doors and windows.

2. Confirm that the ignition key is OFF.

3. NOTE: Steps 5 through 9 must be carried out within 30 seconds.

Turn the ignition key from OFF to RUN.

4. Press the door lock control switch UNLOCK button 3 times.

5. Turn the ignition key from RUN to OFF.

6. Press the door lock control switch UNLOCK button 3 times.

7. Turn the ignition key from OFF to RUN.

8. Verify the horn chirps. This indicates the enable/disable mode and now is ready to accept program changes.

9. Press the door lock control switch LOCK button then the UNLOCK button 1 time to command the module to toggle the auto-unlock feature.

10. Verify that the horn chirps. There should be 1 chirp indicating that auto-unlock feature has been disabled. If 1 chirp is heard, followed by a longer sound of the horn, the auto-unlock feature has just been enabled.

11. Turn the key to the OFF position or wait 2 minutes to exit the enable/disable mode.

12. Verify that the horn chirps once to indicate that a feature has been changed and that auto-unlock has been toggled.