Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSMERCURY2004SABLE V6-3.0L DOHC VIN SREPAIR AND DIAGNOSISSPECIFICATIONSMECHANICAL SPECIFICATIONSENGINECYLINDER BLOCK ASSEMBLYCONNECTING ROD BEARING
2004 Mercury Sable V6-3.0L DOHC VIN S
Connecting Rod Bearing
2004 Mercury Sable V6-3.0L DOHC VIN SSECTION Connecting Rod Bearing
Connecting Rod
Connecting rod-to-pin clearance - standard 0.004 - 0.02 mm (0.0001 - 0.0007 inch)
Connecting rod-to-pin clearance - service limit 0.035 mm (0.0013 inch)
Connecting rod pin bore diameter 21.017 - 21.031 mm (0.827 - 0.828 inch)
Connecting rod length (center-to-center) 138.06 - 138.14 mm (5.435 - 5.438 inch)
Connecting rod maximum allowed bend 0.038 mm per 25 (0.0014 per 0.984 inch)
Connecting rod maximum allowed twist 0.050 mm per 25 (0.0019 per 0.984 inch)
Connecting rod bearing bore diameter 53.015 - 53.035 mm (2.0872 - 2.0879 inch)
Connecting rod bearing-to-crankshaft clearance 0.028 - 0.066 mm (0.001 - 0.0025 inch)
Connecting rod side clearance 0.100 - 0.30 mm (0.0039 - 0.0118 inch)
Connecting rod caps and bolts.
Stage 1: Tighten to 23 Nm (17 ft. lbs.).
Stage 2: Tighten to 43 Nm (32 ft. lbs.).
Connecting rod-to-pin clearance - standard 0.004 - 0.02 mm (0.0001 - 0.0007 inch)
Connecting rod-to-pin clearance - service limit 0.035 mm (0.0013 inch)
Connecting rod pin bore diameter 21.017 - 21.031 mm (0.827 - 0.828 inch)
Connecting rod length (center-to-center) 138.06 - 138.14 mm (5.435 - 5.438 inch)
Connecting rod maximum allowed bend 0.038 mm per 25 (0.0014 per 0.984 inch)
Connecting rod maximum allowed twist 0.050 mm per 25 (0.0019 per 0.984 inch)
Connecting rod bearing bore diameter 53.015 - 53.035 mm (2.0872 - 2.0879 inch)
Connecting rod bearing-to-crankshaft clearance 0.028 - 0.066 mm (0.001 - 0.0025 inch)
Connecting rod side clearance 0.100 - 0.30 mm (0.0039 - 0.0118 inch)
Connecting rod caps and bolts.
Stage 1: Tighten to 23 Nm (17 ft. lbs.).
Stage 2: Tighten to 43 Nm (32 ft. lbs.).
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.