Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSLEXUS2009ES 350 V6-3.5L (2GR-FE)REPAIR AND DIAGNOSISWINDOWS AND GLASSWINDOWSWINDOW SHADESERVICE AND REPAIRINSTALLATION
2009 Lexus ES 350 V6-3.5L (2GR-FE)
Installation
2009 Lexus ES 350 V6-3.5L (2GR-FE)SECTION Installation
INTERIOR: REAR SUNSHADE ASSEMBLY:
INSTALLATION
1. INSTALL REAR SUNSHADE RELAY
NOTE:
When reassembling the rear sunshade assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.
(a) Install the rear sunshade relay with the 2 screws.
(b) Connect the connector.
(c) Engage the 4 claws and install the rear sunshade relay cover.
(d) Install the screw.
2. INSTALL REAR WINDOW SHADE ASSEMBLY
(a) Install the rear window shade assembly, and temporarily tighten the 4 bolts [A] and bolt [B].
(b) Fully tighten the 5 bolts.
(c) Connect the connector.
3. INSTALL NO. 2 PACKAGE TRAY TRIM PANEL ASSEMBLY
(a) Engage the 6 claws and 3 clips, and install the No. 2 package tray trim panel assembly.
4. INSTALL CENTER STOP LIGHT SET Installation
5. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY
(a) Thread the 3 rear seat belt floor anchors into the package tray trim panel assembly.
(b) Insert the rear end of the package tray trim panel assembly into the rear window shade assembly.
(c) Engage the 2 clips and install the package tray trim panel assembly.
6. INSTALL REAR SEAT SHOULDER BELT HOLE COVER Installation
7. CONNECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH Installation
8. CONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH Installation
9. CONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH Installation
10. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY LH Installation
11. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH Installation
12. INSTALL REAR SEAT SIDE GARNISH LH (w/o Rear Seat Side Airbag) Installation
13. INSTALL REAR SEAT SIDE AIRBAG ASSEMBLY LH (w/ Rear Seat Side Airbag) Installation
14. INSTALL REAR SEAT SIDE GARNISH RH (w/o Rear Seat Side Airbag) Installation
15. INSTALL REAR SEAT SIDE AIRBAG ASSEMBLY RH (w/ Rear Seat Side Airbag)
HINT: Use the same procedure for the LH side and RH side.
16. INSTALL REAR DOOR SCUFF PLATE LH Installation
17. INSTALL REAR DOOR SCUFF PLATE RH Installation
18. INSTALL REAR SEATBACK ASSEMBLY Installation
19. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY
20. INSTALL REAR SEAT HEADREST ASSEMBLY
21. INSTALL REAR SEAT CUSHION ASSEMBLY Installation
22. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Rear Seat Side Airbag)
23. PERFORM INITIALIZATION (w/ Rear Seat Side Airbag)
NOTE:
Some systems need initialization after reconnecting the cable to the negative battery terminal Repair Instruction - Initialization.
24. INSPECT SRS WARNING LIGHT (w/ Rear Seat Side Airbag) Diagnosis System
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.