Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSLEXUS2009ES 350 V6-3.5L (2GR-FE)REPAIR AND DIAGNOSISSPECIFICATIONSMECHANICAL SPECIFICATIONSENGINESYSTEM SPECIFICATIONSCOMPONENT TIGHTENING SPECIFICATIONS AND SEQUENCESOIL PUMP
2009 Lexus ES 350 V6-3.5L (2GR-FE)
Oil Pump
2009 Lexus ES 350 V6-3.5L (2GR-FE)SECTION Oil Pump
OIL PUMP COVER
Install the oil pump cover with the 8 bolts.
Torque: 9.1 Nm (93 kgf-cm, 81 in-lbf)
TIMING CHAIN COVER SUB-ASSEMBLY
Temporarily tighten the timing chain cover with the 23 bolts and 2 nuts.
Bolt length:
NOTE: Make sure that there is no oil on the bolt and nut threads.
Fully tighten the bolts in this order: Area 1 and Area 2.
Torque: 21 Nm (214 kgf-cm, 15 ft-lbf)
Fully tighten the bolts in Area 3.
Torque: 21 Nm (214 kgf-cm, 15 ft-lbf)
HINT: Tighten the bolts and nuts in the order of upper to lower as shown in the illustration.
Fully tighten the bolts in Area 4.
mTorque: 43 Nm (438 kgf-cm, 32 ft-lbf)for bolt A
Torque: 21 Nm (214 kgf-cm, 15 ft-lbf)for bolts except bolt A
HINT: Tighten the bolts in the order of lower to upper as shown in the illustration.
Install a new gasket and the chain cover plate with the 4 bolts.
Torque: 9.1 Nm (93 kgf-cm, 81 in-lbf)
Install the oil pump cover with the 8 bolts.
Torque: 9.1 Nm (93 kgf-cm, 81 in-lbf)
TIMING CHAIN COVER SUB-ASSEMBLY
Temporarily tighten the timing chain cover with the 23 bolts and 2 nuts.
Bolt length:
NOTE: Make sure that there is no oil on the bolt and nut threads.
Fully tighten the bolts in this order: Area 1 and Area 2.
Torque: 21 Nm (214 kgf-cm, 15 ft-lbf)
Fully tighten the bolts in Area 3.
Torque: 21 Nm (214 kgf-cm, 15 ft-lbf)
HINT: Tighten the bolts and nuts in the order of upper to lower as shown in the illustration.
Fully tighten the bolts in Area 4.
mTorque: 43 Nm (438 kgf-cm, 32 ft-lbf)for bolt A
Torque: 21 Nm (214 kgf-cm, 15 ft-lbf)for bolts except bolt A
HINT: Tighten the bolts in the order of lower to upper as shown in the illustration.
Install a new gasket and the chain cover plate with the 4 bolts.
Torque: 9.1 Nm (93 kgf-cm, 81 in-lbf)
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.