Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSLEXUS2009ES 350 V6-3.5L (2GR-FE)REPAIR AND DIAGNOSISPOWERTRAIN MANAGEMENTTECHNICAL SERVICE BULLETINS
2009 Lexus ES 350 V6-3.5L (2GR-FE)
Powertrain Management: Technical Service Bulletins
2009 Lexus ES 350 V6-3.5L (2GR-FE)SECTION Technical Service Bulletins
- Recalls
- Customer Interest
- Canada - Engine Control - MIL ON DTC's P0351- P0356 Set
- Canada - MIL ON DTC's P0138/P0158 Set
- Canada - Fuel System - MIL ON, DTC P0505 Set
- Canada - A/T Controls - TCM Calibration, Enhanced Shifting
- Engine - MIL ON/VVT-i DTC's Set - Oil Control Valve
- Engine - Ticking Noises/MIL ON/Multiple VVTi DTC's Set
- Fuel System - MIL ON/DTC P0505 Stored In ECM
- Electrical - Multiple Warning Lamp/Can't Shift From PARK
- A/T Controls - TCM Update For Enhanced Shifting
- Ignition System - MIL ON/Multiple Ign. Coil DTC's Set
- Canada - Engine Control - Engine Ticking Noise/MIL ON/DTC's
- Canada - A/T - Not Shifting Out Of Park
- By Symptom
- Abnormal wear/deterioration
- Customer Interest
- Canada - Engine Control - MIL ON DTC's P0351- P0356 Set
- Canada - MIL ON DTC's P0138/P0158 Set
- Canada - Fuel System - MIL ON, DTC P0505 Set
- Canada - A/T Controls - TCM Calibration, Enhanced Shifting
- Engine - MIL ON/VVT-i DTC's Set - Oil Control Valve
- Engine - Ticking Noises/MIL ON/Multiple VVTi DTC's Set
- Fuel System - MIL ON/DTC P0505 Stored In ECM
- Electrical - Multiple Warning Lamp/Can't Shift From PARK
- A/T Controls - TCM Update For Enhanced Shifting
- Ignition System - MIL ON/Multiple Ign. Coil DTC's Set
- Canada - Engine Control - Engine Ticking Noise/MIL ON/DTC's
- Canada - A/T - Not Shifting Out Of Park
- Driveability
- No shift/Incorrect gear engagement
- Noise
- Odors
- Recalls
- All Technical Service Bulletins
- Vehicle - Flood Damage Inspection And Handling
- Canada - Engine Controls - Accelerator Pedal Sensor Precaution
- Canada - Engine Control - MIL ON DTC's P0351- P0356 Set
- Canada - MIL ON DTC's P0138/P0158 Set
- Canada - Fuel System - MIL ON, DTC P0505 Set
- Canada - Engine - Valve Timing Procedure
- Canada - A/T Controls - TCM Calibration, Enhanced Shifting
- Canada - Engine Control - TDT Lexus diagnostic Tester
- Canada - Engine Control - Failure Initialize CAN Interface
- Canada - Engine Control - ECM Reprogramming Process
- Canada - Engine Control - Oxygen Sensor Location Identification
- Engine Controls - Accelerator Pedal Sensor Service Precautions
- Canada - Exhuast - Sulfur Odor/Smell From Exhaust
- Canada - Engine Control - Software And Calibration Files TDT
- Engine - MIL ON/VVT-i DTC's Set - Oil Control Valve
- Engine - Ticking Noises/MIL ON/Multiple VVTi DTC's Set
- Engine Controls - Techstream(R) ECU Re-Flash Procedure
- Engine Controls - A/F And O2 Sensor Identification
- Engine Controls - MIL ON/DTC P0138/P0158 Diagnostic Tips
- Fuel System - MIL ON/DTC P0505 Stored In ECM
- Electrical - Multiple Warning Lamp/Can't Shift From PARK
- A/T Controls - TCM Update For Enhanced Shifting
- Recall 09V388000: Floor Mat/Accelerator Interference
- Ignition System - MIL ON/Multiple Ign. Coil DTC's Set
- Recall - Floor Mat/Accelerator Pedal Interference
- Canada - Engine Control - Engine Ticking Noise/MIL ON/DTC's
- Canada - A/T - Not Shifting Out Of Park
- Canada - Vehicle - Flood Damage Inspection
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.