Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSLAND ROVER2009RANGE ROVER SPORT (LS) V8-4.4LREPAIR AND DIAGNOSISSPECIFICATIONSMECHANICAL SPECIFICATIONSENGINECYLINDER BLOCK ASSEMBLYCYLINDER BLOCK CRADLE
2009 Land Rover Range Rover Sport (LS) V8-4.4L
Cylinder Block Cradle
2009 Land Rover Range Rover Sport (LS) V8-4.4LSECTION Cylinder Block Cradle
Torque Specifications
Stage 1: Bolts 21 to 32, tighten to 15 Nm (11 ft. lbs.).
Stage 2: Bolts 33 to 34, tighten to 15 Nm (11 ft. lbs.).
Stage 3: Bolts 1 to 10, tighten to 25 Nm (18 ft. lbs.).
Stage 4: Bolts 11 to 20, tighten to 15 Nm (11 ft. lbs.).
Stage 5: Bolts 1 to 10, tighten to 35 Nm (26 ft. lbs.), then a further 135 degrees.
Stage 6: Bolts 11 to 20, tighten to 20 Nm (15 ft. lbs.), then a further 150 degrees.
Stage 7: Bolts 21 to 32, tighten to 20 Nm (15 ft. lbs.), then a further 90 degrees.
Stage 8: Bolts 33 to 34, tighten to 20 Nm (15 ft. lbs.), then a further 150 degrees.
Stage 9: Center punch each of the bolt heads to indicate it has been reused.
Stage 1: Bolts 21 to 32, tighten to 15 Nm (11 ft. lbs.).
Stage 2: Bolts 33 to 34, tighten to 15 Nm (11 ft. lbs.).
Stage 3: Bolts 1 to 10, tighten to 25 Nm (18 ft. lbs.).
Stage 4: Bolts 11 to 20, tighten to 15 Nm (11 ft. lbs.).
Stage 5: Bolts 1 to 10, tighten to 35 Nm (26 ft. lbs.), then a further 135 degrees.
Stage 6: Bolts 11 to 20, tighten to 20 Nm (15 ft. lbs.), then a further 150 degrees.
Stage 7: Bolts 21 to 32, tighten to 20 Nm (15 ft. lbs.), then a further 90 degrees.
Stage 8: Bolts 33 to 34, tighten to 20 Nm (15 ft. lbs.), then a further 150 degrees.
Stage 9: Center punch each of the bolt heads to indicate it has been reused.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.