SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSHONDA2011CR-V EX, 2.4 RE4, BZHAREPAIR AND DIAGNOSISTRANSMISSIONAUTOMATIC TRANSAUTOMATIC TRANSMISSIONA/T INTERLOCK SYSTEMPARK PIN SWITCH REPLACEMENT
2011 Honda CR-V EX, 2.4 RE4, BZHA

Park Pin Switch Replacement

2011 Honda CR-V EX, 2.4 RE4, BZHASECTION Park Pin Switch Replacement
NOTE:
  • The park pin switch is not available from the D3 switch connector harness and the A/T gear position indicator panel light harness; replace the park pin switch, the D3 switch connector harness, A/T gear position indicator panel light harness, and the connector as a set.
  • Refer to the Shift Lever Disassembly and Reassembly (see SHIFT LEVER DISASSEMBLY/REASSEMBLY ) as needed during the following procedures.
  • Do not wipe off the grease that is applied to the portion of the shift lever marked with an asterisk (*) when you disassemble or assemble it because a special grease is used.
  1. Remove the shift lever (see SHIFT LEVER REMOVAL ).
  2. Wrap the end of a flat-tip screwdriver (A) with tape, pry the shift lever knob cover locks (B), and remove the shift lever knob cover (C).
    Fig 1: Pry The Shift Lever Knob Cover Locks
    G00513277Courtesy of AMERICAN HONDA MOTOR CO., INC.
  3. Remove the screws (A), the shift lever button (B), and the spring (C).
    Fig 2: Identifying Shift Lever Button, Spring And Screws
    G06615949Courtesy of AMERICAN HONDA MOTOR CO., INC.
  4. Remove the D3 switch (D) by expanding its locks (E) from the shift lever knob, and remove the shift lever knob (F).
  5. Remove the shift lock solenoid connector and the D3 switch/park pin switch/A/T gear position indicator panel light connector from the shift lever.
  6. Remove the harness wire ties, and disconnect the D3 switch 2P connector (A).
    Fig 3: Identifying D3 Switch 2P Connector
    G06615950Courtesy of AMERICAN HONDA MOTOR CO., INC.
  7. Remove the D3 switch harness and the shift lever ring.
  8. Remove the A/T gear position indicator panel light socket from the indicator panel, and remove the indicator panel.
  9. Release the lock (A) of the shift lock release, and remove the shift lock release and the release spring (B).
    Fig 4: Identifying Release Lock And Release Spring
    G06615951Courtesy of AMERICAN HONDA MOTOR CO., INC.
  10. Remove the shift lever mounting bracket (A), and remove the park pin switch (B).
    Fig 5: Identifying Shift Lever Mounting Bracket And Park Pin Switch
    G06615952Courtesy of AMERICAN HONDA MOTOR CO., INC.
  11. Remove the A/T gear position indicator panel light harness, the park pin switch, the D3 switch connector harness, and the connector assembly, and replace it.
  12. Apply non-hardening thread lock sealant to the screw threads. Install a new park pin switch (A), and secure the switch with the screw.
    Fig 6: Park Pin Switch And Screw With Torque Specification
    G06615953Courtesy of AMERICAN HONDA MOTOR CO., INC.
  13. Install the shift lever mounting bracket.
  14. Install the A/T gear position indicator panel assembly, the shift lever ring, and the D3 switch harness.
  15. Route the D3 switch harness (A), connect the D3 switch 2P connector (B), and install the connector in the holder.
    Fig 7: Identifying D3 Switch Harness And D3 Switch 2P Connector
    G06615954Courtesy of AMERICAN HONDA MOTOR CO., INC.
  16. Tie the harnesses of the D3 switch and the park pin switch at the guide (C) with the harness wire tie (D).
  17. Install the A/T gear position indicator panel light socket in the indicator panel assembly.
    Fig 8: Identifying A/T Gear Position Indicator Panel Light Socket In Indicator Panel Assembly
    G06615955Courtesy of AMERICAN HONDA MOTOR CO., INC.
  18. Route the park pin switch harness, the D3 switch harness, and the A/T gear position indicator panel light harness. Take the slack out of the harnesses, and secure the harnesses (A) with the harness wire tie (B) at the guide (C).
    Fig 9: Identifying Harness Wire Tie And Guide
    G06615956Courtesy of AMERICAN HONDA MOTOR CO., INC.
  19. Install the shift lock solenoid connector and the D3 switch/park pin switch/A/T gear position indicator panel light connector on the shift lever.
  20. Install the shift lock release spring (A) in the shift lock release (B).
    Fig 10: Identifying Shift Lock Release Spring In Shift Lock Release
    G06615957Courtesy of AMERICAN HONDA MOTOR CO., INC.
  21. Install the shift lock release and the release spring on the release shaft end.
  22. Make sure that the release spring end (A) is installed in the shift lock release (B), and the hooked end (C) is on the catch (D).
    Fig 11: Identifying Release Spring End, Shift Lock Release And Hooked End On Catch
    G06615958Courtesy of AMERICAN HONDA MOTOR CO., INC.
  23. Install the shift lever button spring (A) and the shift lever button (B) in the shift lever knob (C), and install the shift lever knob over the shift lever.
    Fig 12: Shift Lever Button Spring And Shift Lever Button In Shift Lever Knob With Torque Specification
    G06615959Courtesy of AMERICAN HONDA MOTOR CO., INC.
  24. Secure the shift lever knob with new screws (D).
  25. Install the D3 switch (E) and the shift lever knob cover (F) on the shift lever knob.
  26. Install the shift lever (see SHIFT LEVER INSTALLATION ).
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.