Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSHONDA2006PILOT EX, 3.5 YF2, J35A9REPAIR AND DIAGNOSIS (SINGLE PAGE)QUICK LOOKUPSCOMMON SPECS & PROCEDURESSPECIFICATIONS INDEX
2006 Honda Pilot EX, 3.5 YF2, J35A9
Specifications Index
2006 Honda Pilot EX, 3.5 YF2, J35A9SECTION Specifications Index
PILOT SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | HVAC SERVICE SPECIFICATIONS | ||
| Torque | See applicable component in HEATING/AIR CONDITIONING article. | ||
| Axle Nut/Hub Nut | |||
| Front | 284 N.m (210 ft. lbs.) | ||
| Rear | 245 N.m (181 ft. lbs.) | ||
| Battery | BATTERY | ||
| Brakes | |||
| Bleeding Sequence | BRAKE SYSTEM BLEEDING | ||
| Disc Brakes | BRAKE SYSTEM SERVICE SPECIFICATIONS | ||
| Torque | See applicable component in CONVENTIONAL BRAKE COMPONENTS article. | ||
| Charging | |||
| Generator | ENGINE ELECTRICAL SERVICE SPECIFICATIONS | ||
| Torque | See applicable figure in ALTERNATOR REMOVAL AND INSTALLATION . | ||
| Drive Belts | |||
| Adjustment | DRIVE BELT INSPECTION | ||
| Belt Routing | COMPONENT LOCATION INDEX & DRIVE BELT ROUTING | ||
| Engine Cooling | |||
| General Service Specifications | ENGINE COOLING SERVICE SPECIFICATIONS | ||
| Radiator Cap Pressure | 93-123 kPa (0.95-1.25 kgf/cm2 , 14-18 psi) | ||
| Thermostat R & I | THERMOSTAT REPLACEMENT | ||
| Water Pump R & I | WATER PUMP REPLACEMENT | ||
| Engine Mechanical | |||
| Compression | ENGINE SERVICE SPECIFICATIONS | ||
| Oil Pressure (176°F (80°C) | 70 kPa (.7 kgf/cm2 , 10 psi) @ idle; 490 kPa (5.0 kgf/cm2 , 71 psi) @ 3000 RPM | ||
| Overhaul | See applicable specifications table in.ENGINE SERVICE SPECIFICATIONS | ||
| Torque | See applicable component in one of the following articles: CYLINDER HEAD ENGINE BLOCK ENGINE LUBRICATION INTAKE MANIFOLD AND EXHAUST SYSTEM |
||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. | ||
| Flywheel/Flex Plate Torque | |||
| A/T | 74 N.m (54 ft. lbs.) | ||
| Fuel System | |||
| Pressure Specification | 380-430 kPa (3.9-4.4 kgf/cm2 , 55-63 psi) | ||
| Fuel Pressure Test Procedure | FUEL PRESSURE TEST | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | NA | ||
| Ignition Wires (Routing) | NA | ||
| Spark Plug (NGK: IZFR5K-11) | |||
| Gap | 1.0-1.1 mm (.039-.043 in.) | ||
| Torque | 18 N.m (13 ft. lbs.) | ||
| Starting | |||
| Starter | STARTER PERFORMANCE TEST | ||
| Torque | STARTER REMOVAL AND INSTALLATION | ||
| Wheel Alignment | |||
| Adjustment Specifications | SUSPENSION SERVICE SPECIFICATIONS | ||
| Torque | |||
| Front | See applicable component in FRONT SUSPENSION article. | ||
| Rear | See applicable component in REAR SUSPENSION article. | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 108 N.m (80 ft. lbs.) | ||
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.