SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSHONDA2002CIVIC SIREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 148 (AUTOMATIC TRANSMISSION)AUTOMATIC TRANSMISSIONA/T GEAR POSITION INDICATOR PANEL ASSEMBLY REPLACEMENT
2002 Honda Civic Si

A/T Gear Position Indicator Panel Assembly Replacement

2002 Honda Civic SiSECTION A/T Gear Position Indicator Panel Assembly Replacement
WARNING: This page is about a different car, the 2006 Honda Odyssey and 2005 Honda Odyssey. However, it is still accessible from the selected car via links, so may be relevant.
  1. Remove the shift lever assembly (see SHIFT LEVER REMOVAL  ).
  2. Pry off the D3 switch cover (A).
    Fig 1: Prying Off D3 Switch Cover
    G03705022Courtesy of AMERICAN HONDA MOTOR CO., INC.
  3. Remove the D3 switch (A) by expanding its locks (B). Remove the screws (C), shift lever button (D), spring (E), shift lever knob (F), and shift lever knob cover (G).
    Fig 2: Removing D3 Switch
    G03705023Courtesy of AMERICAN HONDA MOTOR CO., INC.
  4. Remove the shift lever rod (A), and remove the A/T gear position indicator panel light socket (B).
    Fig 3: Removing Shift Lever Rod
    G03705024Courtesy of AMERICAN HONDA MOTOR CO., INC.
  5. Remove the A/T gear position indicator panel assembly (C).
  6. Disassemble the old A/T gear position indicator panel assembly, and remove the shift lock release (A), release spring (B), and shift lock release link (C).
    Fig 4: Removing Shift Lock Release
    G03705025Courtesy of AMERICAN HONDA MOTOR CO., INC.
  7. Apply silicone grease to the shift lock release, release spring, and shift lock release link.
  8. Install the shift lock release, release spring, and shift lock release link in the new A/T gear position indicator panel (D) and A/T gear position indicator panel bracket (E), and assemble the A/T gear position indicator panel assembly.
  9. Install the A/T gear position indicator panel assembly.
  10. Install the shift lever rod (A) by pointing the bevel (B) of the shift lever rod towards the threaded holes (C), and push it into the bottom. Apply silicone grease to the top of the rod.
    Fig 5: Installing Shift Lever Rod Pointing Bevel Of Shift Lever Rod Towards Threaded Holes
    G03705026Courtesy of AMERICAN HONDA MOTOR CO., INC.
  11. Install the shift lever knob cover (D).
  12. Apply silicone grease to the shift lever button spring (E), and install the spring, shift lever button (F), and shift lever knob (G).
  13. Apply non-hardening thread lock sealant to screw threads, and secure the shift lever knob to the shift lever.
  14. Install the D3 switch (H) and D3 switch cover (I).
  15. Install the shift lever assembly (see SHIFT LEVER INSTALLATION  ).
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.