Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2012FOCUS L4-2.0LREPAIR AND DIAGNOSISHEATING AND AIR CONDITIONINGTESTING AND INSPECTIONPINPOINT TESTSCLIMATE CONTROL - DATCDIAGNOSTIC ROUTINE AC
2012 Ford Focus L4-2.0L
Diagnostic Routine AC
2012 Ford Focus L4-2.0LSECTION Diagnostic Routine AC
Diagnostic Routine AC
Diagnostic Overview
U0155:00
DTC Fault Trigger Conditions
Pinpoint Test
1. VERIFY THE CUSTOMER CONCERN
1. Ignition ON.
2. Verify there is an observable symptom present.
Is an observable symptom present?
2. CHECK THE COMMUNICATION NETWORK
1. Ignition ON.
2. Using a scan tool, perform network test.
Does the IPC (Instrument Panel Cluster) pass the network test?
3. RETRIEVE THE RECORDED DTCs (Diagnostic Trouble Codes) FROM THE IPC (Instrument Panel Cluster) SELF-TEST
1. Using a scan tool, perform IPC (Instrument Panel Cluster) self-test.
2. Check for recorded DTCs (Diagnostic Trouble Codes) from the IPC (Instrument Panel Cluster) self-test.
Is DTC (Diagnostic Trouble Code) U3006:16 or DTC (Diagnostic Trouble Code) U3006:17 recorded?
4. RETRIEVE THE RECORDED DTCs (Diagnostic Trouble Codes) FROM THE HVAC (Heating, Ventilation, and Air Conditioning) MODULE SELF-TEST
1. Using a scan tool, perform HVAC (Heating, Ventilation, and Air Conditioning) module self-test.
2. Check for recorded DTCs (Diagnostic Trouble Codes) from the HVAC (Heating, Ventilation, and Air Conditioning) module self-test.
Is DTC (Diagnostic Trouble Code) U3006:16 or DTC (Diagnostic Trouble Code) U3006:17 recorded?
5. RECHECK THE HVAC (Heating, Ventilation, and Air Conditioning) MODULE DTCs (Diagnostic Trouble Codes)
NOTE: If new modules were installed prior to the DTC (Diagnostic Trouble Code) being set, the module configuration may be incorrectly set during the PMI (Programmable Module Installation) or the PMI (Programmable Module Installation) may not have been carried out.
1. Clear the DTCs (Diagnostic Trouble Codes).
2. Wait 10 seconds.
3. Using a scan tool, perform HVAC (Heating, Ventilation, and Air Conditioning) module self-test.
Is DTC (Diagnostic Trouble Code) U0155:00 still present?
6. CHECK FOR DTC (Diagnostic Trouble Code) U0155:00 SET IN OTHER MODULES
1. Clear all DTCs (Diagnostic Trouble Codes).
2. Ignition OFF.
3. Ignition ON.
4. Wait 10 seconds.
5. Using a scan tool, retrieve all continuous memory DTCs (Diagnostic Trouble Codes).
Is DTC (Diagnostic Trouble Code) U0155:00 set in any other module?
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.