Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2012F 350 2WD SUPER DUTY V8-6.2LREPAIR AND DIAGNOSISPOWERTRAIN MANAGEMENTCOMPUTERS AND CONTROL SYSTEMSTESTING AND INSPECTIONSCAN TOOL TESTING AND PROCEDURESSCAN TOOL SETUP AND FUNCTIONALITY
2012 Ford F 350 2WD Super Duty V8-6.2L
Scan Tool Setup and Functionality
2012 Ford F 350 2WD Super Duty V8-6.2LSECTION Scan Tool Setup and Functionality
SCAN TOOL SETUP AND FUNCTIONALITY
Connect the scan tool to the data link connector (DLC) for communication with the vehicle.
The DLC is located on the driver side of the vehicle under the steering column. It is attached to the instrument panel and accessible from the driver seat.
The DLC is rectangular in design and capable of accommodating up to 16 terminals. The connector has keying features to allow easy connection.
The required scan tool functions are described below:
- monitor, record, and playback of parameter identification (PID)
- freeze frame PID data
- diagnostic test modes; self-test, clear diagnostic trouble codes (DTCs)
- output state control (OSC)
- output test mode (OTM)
- resetting keep alive memory (KAM)
- diagnostic monitoring test results (mode 6) for on board diagnostic (OBD) monitors
- on board system readiness (OBD monitor completion status)
Some of these functions are described. Refer to the scan tool manufacturer's instruction manual for specific information on scan tool setup and operation.
International Standards Organization (ISO) 14229 DTC Descriptions
The ISO 14229 DTC is a set of common requirements for diagnostic systems. The scan tool displays a failure type and a status type with the DTC. The types display additional information the scan tool for the condition that set the DTC. For a list of failure type descriptions, refer to Description and Operation, Powertrain Control Software, International Standards Organization (ISO) 14229 Diagnostic Trouble Code (DTC) Descriptions.
Connect the scan tool to the data link connector (DLC) for communication with the vehicle.
The DLC is located on the driver side of the vehicle under the steering column. It is attached to the instrument panel and accessible from the driver seat.
The DLC is rectangular in design and capable of accommodating up to 16 terminals. The connector has keying features to allow easy connection.
The required scan tool functions are described below:
- monitor, record, and playback of parameter identification (PID)
- freeze frame PID data
- diagnostic test modes; self-test, clear diagnostic trouble codes (DTCs)
- output state control (OSC)
- output test mode (OTM)
- resetting keep alive memory (KAM)
- diagnostic monitoring test results (mode 6) for on board diagnostic (OBD) monitors
- on board system readiness (OBD monitor completion status)
Some of these functions are described. Refer to the scan tool manufacturer's instruction manual for specific information on scan tool setup and operation.
International Standards Organization (ISO) 14229 DTC Descriptions
The ISO 14229 DTC is a set of common requirements for diagnostic systems. The scan tool displays a failure type and a status type with the DTC. The types display additional information the scan tool for the condition that set the DTC. For a list of failure type descriptions, refer to Description and Operation, Powertrain Control Software, International Standards Organization (ISO) 14229 Diagnostic Trouble Code (DTC) Descriptions.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.