Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2012EDGE AWD V6-3.7LREPAIR AND DIAGNOSISWINDOWS AND GLASSTESTING AND INSPECTIONPINPOINT TESTSPINPOINT TEST B: ALL POWER WINDOWS ARE INOPERATIVE
2012 Ford Edge AWD V6-3.7L
Pinpoint Test B: All Power Windows Are Inoperative
2012 Ford Edge AWD V6-3.7LSECTION Pinpoint Test B: All Power Windows Are Inoperative
Glass, Frames and Mechanisms
Pinpoint Test B: All Power Windows are Inoperative - Edge
Refer to Wiring Diagram Set 100, Power Windows for schematic and connector information Electrical Diagrams.
Normal Operation
Under normal operation, voltage is supplied to the LH and RH front window control switches from the accessory delay relay. The accessory delay relay is located in the Body Control Module (BCM).
This pinpoint test is intended to diagnose the following:
- Circuit breaker
- Accessory delay relay
- Wiring, terminals or connectors
- Window control switch
PINPOINT TEST B : ALL POWER WINDOWS ARE INOPERATIVE - EDGE
NOTICE: Use the correct probe adapter(s) from the Flex Probe Kit when making measurements. Failure to use the correct probe adapter(s) may damage the connector.
B1 CHECK VOLTAGE TO THE LH FRONT WINDOW CONTROL SWITCH
- Disconnect: LH Front Window Control Switch C504A.
- Ignition ON.
- Measure the voltage between LH front window control switch C504A-2, circuit CBP01 (BU), harness side and ground.
Is the voltage greater than 10 volts?
Yes
GO to B3.
No
VERIFY circuit breaker 48 (30A) is OK. If OK, GO to B2.
If not OK, REFER to the Wiring Diagrams to identify the possible causes of the circuit short Electrical Diagrams. REPAIR the circuit. TEST the system for normal operation.
B2 CHECK THE LH FRONT WINDOW CONTROL SWITCH VOLTAGE CIRCUIT FOR AN OPEN
- Ignition OFF.
- Disconnect: BCM (Body Control Module) C2280D.
- Measure the resistance between BCM (Body Control Module) C2280D-27, circuit CBP01 (BU), harness side and LH front window control switch C504A-2, circuit CBP01 (BU), harness side.
Is the resistance less than 5 ohms?
Yes
GO to Pinpoint Test L to diagnose the accessory delay relay circuit Pinpoint Test L: The Delayed Accessory Is Inoperative.
No
REPAIR the circuit. TEST the system for normal operation.
B3 CHECK THE LH FRONT WINDOW CONTROL SWITCH GROUND CIRCUIT
- Ignition OFF.
- Disconnect: LH Front Window Control Switch C504B.
- Measure the resistance between LH front window control switch C504B-7, circuit GD133 (BK), harness side and ground.
Is the resistance less than 5 ohms?
Yes
INSTALL a new LH front window control switch. REFER to Window Control Switch . TEST the system for normal operation.
No
REPAIR the circuit. TEST the system for normal operation.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.