Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD1999RANGER 2WD V6-3.0L VIN UREPAIR AND DIAGNOSISMAINTENANCEALIGNMENTSPECIFICATIONS
1999 Ford Ranger 2WD V6-3.0L VIN U
Alignment: Specifications
1999 Ford Ranger 2WD V6-3.0L VIN USECTION Specifications
Caster - 0° Frame Angle [1]
Left Hand 4.0° ± 1.0°
Right Hand 4.4° ± 1.0°
Total/split -0.4° ± 0.7°
Camber
Left Hand -0.5° ± 0.7°
Right Hand -0.5° ± 0.7°
Total/split 0.0° ± 0.7°
Total Toe @ Curb Ride Height [2] 0.06° ± 0.25°
Wheel Track 30.6 mm (1.22 inch)
Dogtracking - Max. (Centerline Of Front
Tires Compared To Centerline Of Rear Tires) 30 mm (1.2 inch)
Clear Vision (Negative Value Is Counterclockwise) 2.4° ± 3.0°
Ride Height
Front
Original Parts 102 mm (4.08 inch) ± 15 mm (0.6 inch)
Replacement Parts 102 mm (4.08 inch) ± 15 mm (0.6 inch)
Rear 178-227 mm (7.12-9.08 inch)
Vehicle Lean (Side-to-Side Height Differences)
Front Wheel Opening 16 mm (0.64 inch)
Rear Wheel Opening 20 mm (0.8 inch)
[1] If vehicle is higher in the rear, add the frame angle to the measured caster. If vehicle if lower in the rear, subtract the frame angle from the measured caster. Compare the total to the specification.
[2] Positive value is toe-in, negative value is toe-out.
Left Hand 4.0° ± 1.0°
Right Hand 4.4° ± 1.0°
Total/split -0.4° ± 0.7°
Camber
Left Hand -0.5° ± 0.7°
Right Hand -0.5° ± 0.7°
Total/split 0.0° ± 0.7°
Total Toe @ Curb Ride Height [2] 0.06° ± 0.25°
Wheel Track 30.6 mm (1.22 inch)
Dogtracking - Max. (Centerline Of Front
Tires Compared To Centerline Of Rear Tires) 30 mm (1.2 inch)
Clear Vision (Negative Value Is Counterclockwise) 2.4° ± 3.0°
Ride Height
Front
Original Parts 102 mm (4.08 inch) ± 15 mm (0.6 inch)
Replacement Parts 102 mm (4.08 inch) ± 15 mm (0.6 inch)
Rear 178-227 mm (7.12-9.08 inch)
Vehicle Lean (Side-to-Side Height Differences)
Front Wheel Opening 16 mm (0.64 inch)
Rear Wheel Opening 20 mm (0.8 inch)
[1] If vehicle is higher in the rear, add the frame angle to the measured caster. If vehicle if lower in the rear, subtract the frame angle from the measured caster. Compare the total to the specification.
[2] Positive value is toe-in, negative value is toe-out.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.