Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD1999F 150 2WD PICKUP V6-4.2L VIN 2REPAIR AND DIAGNOSISRELAYS AND MODULESRELAYS AND MODULES - POWERTRAIN MANAGEMENTRELAYS AND MODULES - COMPUTERS AND CONTROL SYSTEMSALTERNATIVE FUEL CONTROL MODULETECHNICAL SERVICE BULLETINSBI-FUEL SYSTEM - COMPUVALVE REPLACEMENT
1999 Ford F 150 2WD Pickup V6-4.2L VIN 2
Bi-Fuel System - Compuvalve Replacement
1999 Ford F 150 2WD Pickup V6-4.2L VIN 2SECTION Bi-Fuel System - Compuvalve Replacement
Article No.
01-10-6
05/28/01
DRIVEABLITY - BI-FUEL - COMPUVALVE
PRE-REPLACEMENT CHECK LIST - SERVICE TIPS
FORD:
1996-2000 CONTOUR
1994-2001 F-150, F-250 LD
1995-2001 E-250, E-350
1999-2001 SUPER DUTY F SERIES
ISSUE
This article will be used as an aid in diagnosis to avoid unnecessary replacement of the compuvalve on bi-fuel vehicles after normal diagnosis has determined the compuvalve may be faulty.
ACTION
Complete the normal diagnostic methods and pinpoint tests. Should the conclusion be after normal diagnosis to replace the compuvalve, then follow the compuvalve Pre-Replacement Checklist (below) before replacing the compuvalve.
SERVICE INFORMATION
Glossary Of Terms
^ ALT - Alternate Fuel Mode
^ FAP - Fuel Absolute Pressure
^ HPS - High Pressure Solenoid
^ VCL - Vehicle Communications Link
^ AFCM - Alternate Fuel Control Module
^ WDS - Worldwide Diagnostic System
^ DTC - Diagnostic Trouble Code
^ MAP - Manifold Absolute Pressure
^ LPG - Liquid Propane Gas
^ EEC - Electronic Engine Control
NOTE
THE FOLLOWING IS A LIST OF KNOWN MIS-DIAGNOSIS OF THE COMPUVALVE REPLACEMENT ON BI-FUEL VEHICLES.
1. MAP line loose.
2. High FAP from vaporizer breakdown.
3. Incorrect interpretation of DTCs.
4. VCL replacement due to harness faults.
5. Misfire due to leaking 0-rings.
6. Compuvalve replaced without checking HPS circuit for correct resistance.
7. Low FAP due to lockoff fault.
8. LPG fuel filter in backward.
COMPUVALVE PRE-REPLACEMENT CHECKLIST
1. Check communication ability with EEC, AFCM/compuvalve and VCL and compuvalve. Follow the Powertrain Control/Emissions Diagnosis (PC/ED) Workshop Manual procedures for the appropriate vehicle.
2. Check MAP line. Follow normal diagnostic methods and visual checks.
3. Check harness and connection integrity. Follow normal diagnostic methods, basic circuit checks and harness connections.
4. Check current bi-fuel EEC calibration code. Refer to WDS.
5. Check fuel gauge with fuel selector switch in ALT position for fuel level.
6. Check power to compuvalve. Power to the compuvalve is indicated by the following fuel selector switch light status: On steady = OK, On then Off or Flashing (regular and irregular) indicated fault.
7. Check that the arrow on the LPG fuel filter is pointing in the direction of fuel flow.
8. Check base vehicle. Run vehicle in gas mode (e.g., borderline secondary ignition). Follow normal diagnostic methods.
9. Check other applicable TSBs and special service messages.
10. Verify ALT fuel switch status. Refer to Section 1 of the appropriate PC/ED Workshop Manual.
OTHER APPLICABLE ARTICLES: NONE
WARRANTY STATUS: INFORMATION ONLY
OASIS CODES: 490000, 602300, 603300, 608000, 609000, 611000, 623000, 690000, 698298
01-10-6
05/28/01
DRIVEABLITY - BI-FUEL - COMPUVALVE
PRE-REPLACEMENT CHECK LIST - SERVICE TIPS
FORD:
1996-2000 CONTOUR
1994-2001 F-150, F-250 LD
1995-2001 E-250, E-350
1999-2001 SUPER DUTY F SERIES
ISSUE
This article will be used as an aid in diagnosis to avoid unnecessary replacement of the compuvalve on bi-fuel vehicles after normal diagnosis has determined the compuvalve may be faulty.
ACTION
Complete the normal diagnostic methods and pinpoint tests. Should the conclusion be after normal diagnosis to replace the compuvalve, then follow the compuvalve Pre-Replacement Checklist (below) before replacing the compuvalve.
SERVICE INFORMATION
Glossary Of Terms
^ ALT - Alternate Fuel Mode
^ FAP - Fuel Absolute Pressure
^ HPS - High Pressure Solenoid
^ VCL - Vehicle Communications Link
^ AFCM - Alternate Fuel Control Module
^ WDS - Worldwide Diagnostic System
^ DTC - Diagnostic Trouble Code
^ MAP - Manifold Absolute Pressure
^ LPG - Liquid Propane Gas
^ EEC - Electronic Engine Control
NOTE
THE FOLLOWING IS A LIST OF KNOWN MIS-DIAGNOSIS OF THE COMPUVALVE REPLACEMENT ON BI-FUEL VEHICLES.
1. MAP line loose.
2. High FAP from vaporizer breakdown.
3. Incorrect interpretation of DTCs.
4. VCL replacement due to harness faults.
5. Misfire due to leaking 0-rings.
6. Compuvalve replaced without checking HPS circuit for correct resistance.
7. Low FAP due to lockoff fault.
8. LPG fuel filter in backward.
COMPUVALVE PRE-REPLACEMENT CHECKLIST
1. Check communication ability with EEC, AFCM/compuvalve and VCL and compuvalve. Follow the Powertrain Control/Emissions Diagnosis (PC/ED) Workshop Manual procedures for the appropriate vehicle.
2. Check MAP line. Follow normal diagnostic methods and visual checks.
3. Check harness and connection integrity. Follow normal diagnostic methods, basic circuit checks and harness connections.
4. Check current bi-fuel EEC calibration code. Refer to WDS.
5. Check fuel gauge with fuel selector switch in ALT position for fuel level.
6. Check power to compuvalve. Power to the compuvalve is indicated by the following fuel selector switch light status: On steady = OK, On then Off or Flashing (regular and irregular) indicated fault.
7. Check that the arrow on the LPG fuel filter is pointing in the direction of fuel flow.
8. Check base vehicle. Run vehicle in gas mode (e.g., borderline secondary ignition). Follow normal diagnostic methods.
9. Check other applicable TSBs and special service messages.
10. Verify ALT fuel switch status. Refer to Section 1 of the appropriate PC/ED Workshop Manual.
OTHER APPLICABLE ARTICLES: NONE
WARRANTY STATUS: INFORMATION ONLY
OASIS CODES: 490000, 602300, 603300, 608000, 609000, 611000, 623000, 690000, 698298
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.