Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSDODGE2007MAGNUM SRT-8 V8-6.1L VIN 3REPAIR AND DIAGNOSISRELAYS AND MODULESRELAYS AND MODULES - BRAKES AND TRACTION CONTROLELECTRONIC BRAKE CONTROL MODULELOCATIONSMODULE-ANTILOCK BRAKES
2007 Dodge Magnum SRT-8 V8-6.1L VIN 3
Module-Antilock Brakes
2007 Dodge Magnum SRT-8 V8-6.1L VIN 3SECTION Module-Antilock Brakes
Component ID: 238
Component : MODULE-ANTILOCK BRAKES
Connector:
Name : MODULE-ANTILOCK BRAKES
Color : BLACK
# of pins : 47
Qualifier : (ESP)
Pin Description Circuit
1 FUSED B(+) A107 10TN/RD
2 - -
3 - -
4 - -
5 - -
6 - -
7 - -
8 FUSED IGNITION SWITCH OUTPUT (RUN-START) F202 20PK/GY
9 - -
10 - -
11 - -
12 CAN C BUS (+) D65 20WT/LG
13 CAN C BUS (-) D64 20WT/LB
14 - -
15 - -
16 GROUND Z903 10BK/DG
17 - -
18 DYNAMICS SENSOR HIGH DATA LINK D52 20WT/LB
19 DYNAMICS SENSOR LOW DATA LINK D51 20WT/BR
20 - -
21 - -
22 DYNAMICS SENSOR SUPPLY G4 20VT/LB
23 - -
24 - -
25 - -
26 - -
27 - -
28 - -
29 DYNAMICS SENSOR GROUND G94 20VT/DB
30 - -
31 - -
32 FUSED B(+) A111 14DG/RD
33 RIGHT FRONT WHEEL SPEED SENSOR SIGNAL B6 20DG/WT
34 RIGHT FRONT WHEEL SPEED SENSOR SUPPLY B7 20DG/VT
35 STOP LAMP RELAY CONTROL B221 20DG
36 LEFT REAR WHEEL SPEED SENSOR SUPPLY B4 20DG/GY
37 LEFT REAR WHEEL SPEED SENSOR SIGNAL B3 20DG/YL
38 - -
39 - -
40 - -
41 - -
42 RIGHT REAR WHEEL SPEED SENSOR SIGNAL B1 20DG/OR
43 RIGHT REAR WHEEL SPEED SENSOR SUPPLY B2 20DG/LB
44 - -
45 LEFT FRONT WHEEL SPEED SENSOR SUPPLY B9 20DG/LG
46 LEFT FRONT WHEEL SPEED SENSOR SIGNAL B8 20DG/TN
47 GROUND Z903 10BK/DG
Component Location - 6
Fig. 6:
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.