Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHRYSLER2003300M V6-3.5L VIN MREPAIR AND DIAGNOSISWINDOWS AND GLASSWINDOWSPOWER WINDOW SWITCHSERVICE AND REPAIR
2003 Chrysler 300M V6-3.5L VIN M
Power Window Switch: Service and Repair
2003 Chrysler 300M V6-3.5L VIN MSECTION Service and Repair
REMOVAL
MASTER SWITCH
INTREPID AND CONCORDE
1. Open hood and disconnect the negative battery cable remote terminal from the remote battery post.
2. Remove driver's door trim panel. (Refer to BODY/DOOR - FRONT/TRIM PANEL - REMOVAL).
3. Remove three mounting screws.
4. Remove switch and disconnect wire connector.
LHS and 300M
1. Open hood and disconnect the negative battery cable remote terminal from the remote battery post.
2. Using a trim stick (special tool #C-4755) or equivalent, gently pry up on switch trim bezel and lift up and out of trim panel.
3. Disconnect wire connector from rear of switch and remove switch from vehicle.
PASSENGER SWITCH
1. Open hood and disconnect the negative battery cable remote terminal from the remote battery post.
2. Remove passenger door trim panel. (Refer to BODY/DOOR - FRONT/TRIM PANEL - REMOVAL).
3. Disconnect switch wire connector.
4. Remove switch from bezel and vehicle.
REAR DOOR SWITCHES
1. Open hood and disconnect the negative battery cable remote terminal from the remote battery post.
2. Open rear door.
3. Using a trim stick (special tool #C-4755), gently pry up on rear edge of switch pushing forward as you pry up on switch bezel.
4. Pull switch up and out of rear door trim panel.
5. Using a trim stick, gently pry out on retaining tabs on side of switch connector and pull connector from switch.
6. Remove switch from vehicle.
INSTALLATION
MASTER SWITCH
INTREPID AND CONCORDE
1. Install switch and wire connector.
2. Install three mounting screws.
3. Install drivers door trim panel. (Refer to BODY/DOOR - FRONT/TRIM PANEL - INSTALLATION).
4. Connect negative battery cable remote terminal.
LHS and 300M
1. Install wire connector to switch.
2. Install switch to trim panel.
3. Connect negative battery cable remote terminal.
PASSENGER SWITCH
1. Install switch and wire connector.
2. Install door trim panel. (Refer to BODY/DOOR - FRONT/TRIM PANEL - INSTALLATION).
3. Connect negative battery cable remote terminal.
REAR DOOR SWITCHES
1. Install connector to switch.
2. Insert switch into door trim panel.
3. Connect negative battery cable remote terminal.
MASTER SWITCH
INTREPID AND CONCORDE
1. Open hood and disconnect the negative battery cable remote terminal from the remote battery post.
2. Remove driver's door trim panel. (Refer to BODY/DOOR - FRONT/TRIM PANEL - REMOVAL).
3. Remove three mounting screws.
4. Remove switch and disconnect wire connector.
LHS and 300M
1. Open hood and disconnect the negative battery cable remote terminal from the remote battery post.
2. Using a trim stick (special tool #C-4755) or equivalent, gently pry up on switch trim bezel and lift up and out of trim panel.
3. Disconnect wire connector from rear of switch and remove switch from vehicle.
PASSENGER SWITCH
1. Open hood and disconnect the negative battery cable remote terminal from the remote battery post.
2. Remove passenger door trim panel. (Refer to BODY/DOOR - FRONT/TRIM PANEL - REMOVAL).
3. Disconnect switch wire connector.
4. Remove switch from bezel and vehicle.
REAR DOOR SWITCHES
1. Open hood and disconnect the negative battery cable remote terminal from the remote battery post.
2. Open rear door.
3. Using a trim stick (special tool #C-4755), gently pry up on rear edge of switch pushing forward as you pry up on switch bezel.
4. Pull switch up and out of rear door trim panel.
5. Using a trim stick, gently pry out on retaining tabs on side of switch connector and pull connector from switch.
6. Remove switch from vehicle.
INSTALLATION
MASTER SWITCH
INTREPID AND CONCORDE
1. Install switch and wire connector.
2. Install three mounting screws.
3. Install drivers door trim panel. (Refer to BODY/DOOR - FRONT/TRIM PANEL - INSTALLATION).
4. Connect negative battery cable remote terminal.
LHS and 300M
1. Install wire connector to switch.
2. Install switch to trim panel.
3. Connect negative battery cable remote terminal.
PASSENGER SWITCH
1. Install switch and wire connector.
2. Install door trim panel. (Refer to BODY/DOOR - FRONT/TRIM PANEL - INSTALLATION).
3. Connect negative battery cable remote terminal.
REAR DOOR SWITCHES
1. Install connector to switch.
2. Insert switch into door trim panel.
3. Connect negative battery cable remote terminal.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.