Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHRYSLER1999300M V6-3.5L VIN GREPAIR AND DIAGNOSISCRUISE CONTROLCRUISE CONTROL SERVO CABLESERVICE AND REPAIR
1999 Chrysler 300M V6-3.5L VIN G
Cruise Control Servo Cable: Service and Repair
1999 Chrysler 300M V6-3.5L VIN GSECTION Service and Repair
REMOVAL
1. Disconnect the negative battery cable.
2. Remove throttle cable bracket from intake manifold.
3. Remove speed control cable from throttle cam by sliding clasp out hole used for throttle cable.
4. Remove the throttle cable (with retaining tab) and then slide cable speed control cable out from bracket.
5. Remove one bolt and two nuts from servo bracket.
6. Disconnect electrical connectors and vacuum hose.
7. Remove two nuts attaching mounting bracket and speed control cable to servo.
8. Pull cable away from servo to expose retaining clip and remove clip attaching cable to servo.
9. Remove servo mounting bracket.
INSTALLATION
1. Slide speed control cable into bracket and with locator positioned into notch in bracket, then slide throttle cable into bracket and engage retaining tab.
2. Rotate the throttle cam forward to the wide open position and install speed control cable clasp.
3. Rotate the throttle cam forward to the wide open position and install throttle cable clasp.
4. Install throttle cable bracket and tighten bolts.
5. Route cable through bracket and install retaining clip to cable at servo.
6. Insert servo studs through holes in mounting bracket and speed control cable.
7. Install nuts, tighten to 6.7 N.m (60 in. lbs.).
8. Connect vacuum hose to servo.
9. Connect electrical connector.
10. Install servo and bracket and tighten bolts.
11. Connect negative battery cable.
1. Disconnect the negative battery cable.
2. Remove throttle cable bracket from intake manifold.
3. Remove speed control cable from throttle cam by sliding clasp out hole used for throttle cable.
4. Remove the throttle cable (with retaining tab) and then slide cable speed control cable out from bracket.
5. Remove one bolt and two nuts from servo bracket.
6. Disconnect electrical connectors and vacuum hose.
7. Remove two nuts attaching mounting bracket and speed control cable to servo.
8. Pull cable away from servo to expose retaining clip and remove clip attaching cable to servo.
9. Remove servo mounting bracket.
INSTALLATION
1. Slide speed control cable into bracket and with locator positioned into notch in bracket, then slide throttle cable into bracket and engage retaining tab.
Disconnecting Throttle Cable - Typical:
2. Rotate the throttle cam forward to the wide open position and install speed control cable clasp.
3. Rotate the throttle cam forward to the wide open position and install throttle cable clasp.
4. Install throttle cable bracket and tighten bolts.
5. Route cable through bracket and install retaining clip to cable at servo.
6. Insert servo studs through holes in mounting bracket and speed control cable.
7. Install nuts, tighten to 6.7 N.m (60 in. lbs.).
8. Connect vacuum hose to servo.
9. Connect electrical connector.
10. Install servo and bracket and tighten bolts.
11. Connect negative battery cable.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.