Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Installation Procedure
Wiring Harness Bracket (1) - Install
Steering Column (2) - Install
- Steering Column Nut (1) - Install and hand tighten [4x]
- CAUTION:
Refer to Fastener Caution .
Steering Column Nut (1) - Tighten in sequence [4x] - Fastener Specifications
- Connect the steering column electrical connectors.
- NOTE:
Ensure the match marks on the upper intermediate steering shaft and steering column are aligned.
Intermediate Steering Shaft (1) @ Steering Column - Install
If a NEW threaded component is being installed, loosen the adhesive using a metal pick or similar tool before proceeding. If threaded component is reused, prepare the threaded component using the following steps:
- Remove any loose cured adhesive from the external threads of the component using a lint free cloth.
- Thread the cleaned component into the internal mating threads and remove to loosen trapped cured adhesive.
- Remove loose debris from internal and external threads using compressed air.
- Apply liquid thread locking adhesive in a strip along half of the length of the external threads, starting at the tip, just prior to installation. Adhesives, Fluids, Lubricants, and Sealers
- Intermediate Steering Shaft Upper Bolt (1) - Install and tighten - Fastener Specifications
Wiring Harness (3) - Install
- Wiring Harness Retainer (2) - Install
- Wiring Harness Retainer (1) - Install
Floor Front Air Outlet Duct - Left Side (2) - Install
- Push Pin (1) - Install
Instrument Panel Knee Bolster Deflector (2) - Install
- Instrument Panel Knee Bolster Deflector Bolt (1) - Install and tighten [4x] - Fastener Specifications
Hood Primary Latch Release Cable Handle (1) - Install
- WARNING:
When removing, handling or installing this component wear protective gloves. The sharp edges on the component may be very sharp and may cause injury.
Instrument Panel Knee Bolster (1) - Install
Instrument Panel Knee Bolster Bolt (1) - Install and tighten [3x] - Fastener Specifications
Data Link Connector (2) - Install
- Data Link Connector Bolt (1) - Install and tighten [2x] - Fastener Specifications
Insert the tab at the top of the instrument panel outer trim cover (1) into the instrument panel before installing.
- Instrument Panel Outer Trim Cover (1) - Install
Instrument Panel Lower Trim Panel Insulator - Left Side (2) - Install
- Instrument Panel Lower Trim Panel Insulator Retainer (1) - Install [3x]
Install the turn signal switch bracket (1) as an assembly.
- Ensure the tabs on the turn signal switch bracket are fully engaged.
Tighten the turn signal switch bracket band clamp (1) to specification. Fastener Specifications
Wiring Harness Clip (1) - Install [3x]
- Electrical Connector (2) - [2x]
- Ensure the steering wheel airbag coil is CENTERED during installation. Steering Wheel Airbag Coil Centering
- NOTE:
Ensure the 5 integral retainers are fully engaged.
Steering Wheel Airbag Coil (1) - Install
- Connect the electrical connector.
Connect the electrical connector, if equipped.
- Instrument Panel Steering Column Lower Trim Cover (1) - Install
Instrument Panel Steering Column Lower Trim Cover Bolt (1) - Install and tighten [3x] - Fastener Specifications
Secure the instrument panel steering column upper trim cover (1) to the instrument panel steering column lower trim cover.
Connect the electrical connector.
- Steering Wheel (2) - Install
- If a NEW threaded component is being installed, loosen the adhesive using a metal pick or similar tool before proceeding. If threaded component is reused, prepare the threaded component using the following steps:
- Remove any loose cured adhesive from the external threads of the component using a lint free cloth.
- Thread the cleaned component into the internal mating threads and remove to loosen trapped cured adhesive.
- Remove loose debris from internal and external threads using compressed air.
- Apply liquid thread locking adhesive in a strip along half of the length of the external threads, starting at the tip, just prior to installation. Adhesives, Fluids, Lubricants, and Sealers
- Steering Wheel Bolt (1) - Install and tighten - Fastener Specifications
Connect the electrical connector.
- Steering Wheel Airbag (1) - Install
Steering Wheel Airbag Bolt (1) - Install and tighten [2x] - Fastener Specifications
Install the left and right steering wheel airbag access hole covers (1).
- Enable the SIR System. SIR Disabling and Enabling
- Center the steering angle sensor. Steering Wheel Position Sensor Centering
- If battery was disconnected for steering column replacement, wait for all modules to fall asleep. This can be done by closing all vehicle closures (doors, trunk, hood) and waiting for three minutes without actuating any vehicle functions or pushing any buttons.
- Perform functionality check of tilt and telescoping features.
Support the steering column while installing the steering column nuts.
After installation of the steering wheel airbag module to the steering wheel, slightly pull the module outward. If there is no give on the airbag module then it is secured correctly. If the airbag module is not fully attached personal injury could result.
NO RELATED
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.