SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2025TAHOE PPV, RWDREPAIR AND DIAGNOSIS (SINGLE PAGE)ELECTRICALBODY ELECTRICALCOMPONENT CONNECTOR END VIEWS (E42R-K19)COMPONENT CONNECTOR END VIEWSK9 BODY CONTROL MODULE X2
2025 Chevrolet Tahoe PPV, RWD

K9 Body Control Module X2

2025 Chevrolet Tahoe PPV, RWDSECTION K9 Body Control Module X2
GM5204222Courtesy of GENERAL MOTORS COMPANY
Connector Part Information
  • Harness Type:Instrument Panel Wiring Harness
  • OEM Connector: 160028-0015
  • Service Connector: 13534980
  • Description: 32-Way F 0.5 NANO, 1.2 MCON, stAK50h Series (PK with GY Inner Connector)
Terminal Part Information

Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool
I 19370262 EL-35616-58 (BK) EL-38125-58
II 84729890 J-35616-12 (BU) J-38125-215A
Pin Size Color Circuit Function Terminal Type ID Option
1 0.5 GY 157 Interior Lamp Control II -
2 - 4 - - - Not Occupied - -
5 0.35 BU / GN 5723 Ignition Mode Switch Mode Voltage I -
6 - 8 - - - Not Occupied - -
9 0.35 VT / YE 5526 Tap Up/Tap Down Switch Signal I -
10 0.35 WH / BN 2203 Enhanced Driver Mode 2 Switch Signal I -
11 - - - Not Occupied - -
12 0.35 YE / BU 1714 Windshield Wiper Switch Low Signal I -
13 0.35 BN / GN 11875 Cruise Control Bank 2 Switch Signal I -
14 0.35 GY / GN 11874 Cruise Control Bank 1 Switch Signal I -
15 - - - Not Occupied - -
16 0.35 BN / BK 5720 Ignition Mode Switch Accessory LED Signal I -
17 - 18 - - - Not Occupied - -
19 0.35 WH / VT 103 Headlamp Switch On Signal I -
20 0.35 GN / GY 13 Headlamp Switch Park Lamp Signal I -
21 0.35 GN / BN 306 Headlamp Switch Off Signal I -
22 0.35 GY / BU 3602 Curb View Enable Signal I -
23 0.35 VT / BU 2916 Right Turn Signal Switch Signal I -
24 - - - Not Occupied - -
25 0.35 BK / GY 6009 Windshield Wiper Switch Low Reference I -
26 0.35 WH / BK 94 Windshield Washer Switch Signal I -
27 0.35 YE / BN 307 Headlamp Switch Flash Signal I -
28 0.35 GN / WH 3287 Horn Switch Signal I -
29 0.35 WH / GN 2915 Left Turn Signal Switch Signal I -
30 0.35 BK / YE 407 Sensor Low Reference I -
31 0.35 GN / WH 111 Hazard Warning Switch Signal I -
32 0.35 WH 524 High Beam Select Switch High Beam Signal I -
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.