SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2025TAHOE PPV, 4WDREPAIR AND DIAGNOSIS (SINGLE PAGE)ACCESSORIES & EQUIPMENTANTI-THEFT SYSTEMSKEYLESS ENTRY SYSTEM AND REMOTE FUNCTIONSDIAGNOSTIC INFORMATION AND PROCEDURESDTC B1444 (ATH)CIRCUIT/SYSTEM TESTING
2025 Chevrolet Tahoe PPV, 4WD

Circuit/System Testing

2025 Chevrolet Tahoe PPV, 4WDSECTION Circuit/System Testing
NOTE:

Verify the antenna is installed correctly and not damaged.

  1. Ignition OFF, disconnect the harness connector at the T10K Keyless Entry Antenna - Center Console Rear, ignition ON.
  2. Test for less than 1 V between the signal circuit terminal 1 and ground.
    • If 1 V or greater 
    1. Ignition OFF, disconnect the harness connector at the K9 Body Control Module, ignition ON.
    2. Test for less than 1 V between the signal circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K9 Body Control Module.
    • Go to next step: If less than 1 V 
    3. NOTE:

    When using the MIN MAX function, autorange on the DMM may not function properly. To ensure accurate test results, turn off autorange and manually set the DMM range to 000.0 V.

  3. Ignition OFF, install a DMM between the signal circuit terminal 1 and ground. Set the DMM to capture DC voltage using the MIN MAX function. Turn off autorange and manually set the DMM range to 000.0 V.
  4. Activate the antenna by pressing the Stop/Start switch.
  5. Verify the MAX voltage captured by the DMM is greater than 1 V.
    • If 1 V or less 
    1. Ignition OFF, disconnect the harness connector at the K9 Body Control Module.
    2. Test for infinite resistance between the signal circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • Go to next step: If infinite resistance
    3. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K9 Body Control Module.
    • Go to next step: If greater than 1 V 
  6. Test for less than 1 V between the low reference circuit terminal 2 and ground.
    • If 1 V or greater 
    1. Ignition OFF, disconnect the harness connector at the K9 Body Control Module, ignition ON.
    2. Test for less than 1 V between the low reference circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K9 Body Control Module.
    • Go to next step: If less than 1 V 
    7. NOTE:

    When using the MIN MAX function, autorange on the DMM may not function properly. To ensure accurate test results, turn off autorange and manually set the DMM range to 000.0 V.

  7. Install a DMM between the signal circuit terminal 1 and the low reference circuit terminal 2. Set the DMM to capture DC voltage using the MIN MAX function. Turn off autorange and manually set the DMM range to 000.0 V.
  8. Activate the antenna by pressing the Stop/Start switch.
  9. Verify the MAX voltage captured by the DMM is greater than 1 V.
    • If 1 V or less 
    1. Ignition OFF, disconnect the harness connector at the K9 Body Control Module.
    2. Test for infinite resistance between the low reference circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • Go to next step: If infinite resistance
    3. Test for less than 2 Ω in the low reference circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K9 Body Control Module.
    • Go to next step: If greater than 1 V 
  10. Replace the T10K Keyless Entry Antenna - Center Console Rear.
  11. Activate the antenna by pressing the Stop/Start switch a minimum of three times to meet the conditions for setting the DTC.
  12. Verify DTC B1444 is not set.
    • If DTC B1444 is set 

      Replace the K9 Body Control Module.

    • Go to next step: If DTC B1444 is not set 
  13. All OK.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.