K219 Lighting Control Module X5

2025 Chevrolet Tahoe Commercial, 4WDSECTION K219 Lighting Control Module X5
GM5203373Courtesy of GENERAL MOTORS COMPANY
Connector Part Information
  • Harness Type: Body Wiring Harness
  • OEM Connector: 160029-0013
  • Service Connector: 13534975
  • Description: 29-Way F 0.5 NANO, 1.2 MCON, stAK50h Series (BU with GY Inner Connector)
Terminal Part Information

Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool
I 19370262 EL-35616-58 (BK) EL-38125-58
II 84729890 J-35616-12 (BU) J-38125-215A
Pin Size Color Circuit Function Terminal Type ID Option
1 0.5 VT 8866 Police Liftgate Strobe Control II -
2 0.5 BN / GY 6995 Right Rear Park Lamp Control II -
3 0.5 BN / GY 5061 Left Front Fog Lamp Control II -
4 0.5 BU / VT 1335 Right Rear Turn Signal Lamp Control 2 II -
5 0.5 GN / WH 24 Backup Lamp Control II -
6 0.5 BN / BU 6993 Left Rear Park Lamp Control II -
7 - - - Not Occupied - -
8 0.5 BU / WH 1334 Left Rear Turn Signal Lamp Control 2 II -
9 0.35 GN / GY 2115 Right Turn Signal Lamp Control 2 I -
10 0.35 WH / GY 2114 Left Turn Signal Lamp Control 2 I -
11 0.35 GY 1715 Windshield Wiper Switch High Signal I -
13 0.35 BU / BN 7539 Right Front DRL Control I -
14 - - - Not Occupied - -
15 0.35 GY / GN 6190 Liftgate Window/Rear Compartment Lid, Exterior Unlatch Signal I -
16 0.35 WH / YE 7541 Right Rear Stop Lamp Control I -
17 - - - Not Occupied - -
18 0.35 VT / WH 1139 Run/Crank Ignition 1 Voltage I -
20 - 21 - - - Not Occupied - -
22 0.35 GN / WH 2270 Rear Window Washer Relay Control I -
23 0.35 WH / VT 6567 Rear Turn Signal Lamp Feedback Signal I -
24 0.35 WH / BK 7544 Right Rear Turn Signal Lamp Feedback Signal I -
25 0.35 BN / YE 820 Center High Mounted Stop Lamp Supply Voltage I -
26 0.35 GN / BN 319 Right Rear Trailer Stop/Turn Lamp Control I -
27 0.35 BU / BN 38 Backup Lamp Relay Control I -
28 0.35 GY / YE 7542 Left Rear Stop Lamp Control I -
29 0.35 GY / BU 7538 Left Front DRL Control I -
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • You smell fuel, burning insulation, or see smoke.
  • Brakes feel soft, pull hard to one side, or make grinding noises.
  • The engine overheats, stalls repeatedly, or misfires under load.
  • You are missing required tools, torque specs, or safe lifting equipment.
  • You are not confident in the next step or safety outcome.