Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Installation Procedure
Windshield (1) - Install - Adhesive Installation of Windshields
- With the aid of an assistant, install the windshield (1) and locating pin (2) to the vehicle.
Clean the inside of the windshield before installing the windshield multifunction sensor mount bracket (1).
- Windshield Multifunction Sensor Mount Bracket (1) - Install
Windshield Outside Moisture/Ambient Light and Humidity Sensor (1) - Install NEW
- Connect the electrical connector.
Front View Camera (1) - Install
- Slide the front view camera (1) forward to engage and rotate the front view camera upward and secure the retaining tabs.
- Connect the electrical connector.
Inside Rearview Mirror (2) - Install
- Inside Rearview Mirror Bolt (1) - Install and tighten - Fastener Specifications
- Connect the electrical connectors.
Windshield Multifunction Sensor Mount Bracket Cover (1) - Install
- NOTE:
Some components not shown for graphic clarity.
Windshield Multifunction Sensor Mount Bracket Cover Insert (1) - Install
- Enable the SIR System. SIR Disabling and Enabling
Windshield Wiper System Module Shield (1) - Install
Air Inlet Grille Panel (2) - Install
- Rear Window Washer Nozzle Extension Hose - Connect [2x]
- Rear Window Washer Solvent Container Hose - Connect
- Air Inlet Grille Panel Retainer (1) - Install [8x]
Hood Rear Outer Air Inlet Seal (2) - Install [2x]
- Hood Rear Outer Air Inlet Seal Retainer (1) - Install [2x]
Air Inlet Grille Panel Extension - Right Side (1) - Install
- Air Inlet Grille Panel Retainer (2) - Install
- Remove the double layer of masking tape around the perimeter of the painted surfaces.
- Using a 50/50 mixture of isopropyl alcohol and clean drinkable water with a clean towel, remove any left over adhesive residue from the masking tape.
Air Inlet Grille Panel Extension - Left Side (1) - Install
- Remove the double layer of masking tape around the perimeter of the painted surfaces.
- Using a 50/50 mixture of isopropyl alcohol and clean drinkable water with a clean towel, remove any left over adhesive residue from the masking tape.
Clean the left and right side windshield wiper transmission pivot shaft splines with a soft wire brush before installing the windshield wiper arm (3).
- Windshield Wiper Arm (3) - Install [2x]
- Windshield Wiper Arm Nut (2) - Install and tighten [2x] - Fastener Specifications
- Windshield Wiper Arm Finish Cap (1) - Install [2x]
If required, realign the windshield wipers to their respective alignment circles (1) on the windshield.
- Lubricate the windshield with clean washer fluid.
- Run the windshield wipers for two complete cycles then turn off the windshield wipers.
- Ensure the windshield wipers are in the full park position.
Refer to Fastener Caution .
NO RELATED
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.