Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Installation Procedure
Automatic Transmission Electronic Control (5) @ Turn Signal Switch Bracket (3) - Install
- Automatic Transmission Electronic Control Bolt (4) @ Turn Signal Switch Bracket (3) - Install and tighten [2x] - Fastener Specifications
- Turn Signal Switch (1) @ Turn Signal Switch Bracket (3) - Install
- Turn Signal Switch Bolt (2) @ Turn Signal Switch Bracket (3) - Install and tighten [2x] - Fastener Specifications
Install the turn signal switch bracket (1) as an assembly.
- NOTE:
Some components not shown for graphic clarity.
Engage the left and right turn signal switch bracket retaining tabs (1).
Tighten the turn signal switch bracket band clamp (1) to specification. Fastener Specifications
Wiring Harness Clip (1) - Install
- Connect the electrical connector. (2)
- NOTE:
Some components not shown for graphic clarity.
Wiring Harness Clip (2) - Install
- Connect the electrical connector. (1)
- NOTE:
Ensure the 5 integral retainers are fully engaged.
Ensure the steering wheel airbag coil is CENTERED during installation. Steering Wheel Airbag Coil Centering
- Steering Wheel Airbag Coil (1) - Install
- Connect the electrical connector.
{If equipped} Connect the electrical connectors and install the wiring harness retainers as necessary.
- Instrument Panel Steering Column Lower Trim Cover (1) - Install
Instrument Panel Steering Column Lower Trim Cover Bolt (1) - Install and tighten [3x] - Fastener Specifications
{If equipped} Connect the electrical connector and install the wiring harness retainers as necessary.
- Secure the instrument panel steering column upper trim cover (1) to the instrument panel steering column lower trim cover.
Steering Wheel (2) - Install
- Connect the electrical connector.
- If a NEW threaded component is being installed, loosen the adhesive using a metal pick or similar tool before proceeding. If threaded component is reused, prepare the threaded component using the following steps:
- Remove any loose cured adhesive from the external threads of the component using a lint free cloth.
- Thread the cleaned component into the internal mating threads and remove to loosen trapped cured adhesive.
- Remove loose debris from internal and external threads using compressed air.
- Apply liquid thread locking adhesive in a strip along half of the length of the external threads, starting at the tip, just prior to installation. Adhesives, Fluids, Lubricants, and Sealers
- Steering Wheel Bolt (1) - Install and tighten - Fastener Specifications
Connect the electrical connectors.
- Install any connector position assurance (CPA) devices or secondary locks.
- Steering Wheel Airbag (1) - Install
Steering Wheel Airbag Bolt (1) - Install and tighten [2x] - Fastener Specifications
Steering Wheel Airbag Access Hole Cover - Left Side and Right Side (1) - Install [2x]
- Enable the SIR System. SIR Disabling and Enabling
- Return the steering column to the original position.
Refer to Fastener Caution .
After installation of the steering wheel airbag module to the steering wheel, slightly pull the module outward. If there is no give on the airbag module then it is secured correctly. If the airbag module is not fully attached personal injury could result.
NO RELATED
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.