Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2025EQUINOX RS, FWDREPAIR AND DIAGNOSIS (SINGLE PAGE)QUICK LOOKUPSWIRING DIAGRAMSCOMPONENT CONNECTOR END VIEWS (K56-M64)COMPONENT CONNECTOR END VIEWSK219 LIGHTING CONTROL MODULE X4
2025 Chevrolet Equinox RS, FWD
K219 Lighting Control Module X4
2025 Chevrolet Equinox RS, FWDSECTION K219 Lighting Control Module X4
Connector Part Information
|
Terminal Part Information
| Terminal Type ID | Terminated Lead | Diagnostic Test Probe | Terminal Removal Tool |
|---|---|---|---|
| I | 19370262 | EL-35616-58 (BK) | EL-38125-58 |
| II | 87814662 | J-35616-4A (PU) | J-38125-557 |
| Pin | Size | Color | Circuit | Function | Terminal Type ID | Option |
|---|---|---|---|---|---|---|
| 1 - 2 | - | - | - | Not Occupied | - | - |
| 3 | 0.35 | BU / GN | 4103 | AUTOSAR CAN Bus [+] 9 Serial Data | I | - |
| 4 | 0.35 | WH / GN | 4102 | AUTOSAR CAN Bus [-] 9 Serial Data | I | - |
| 5 | 0.35 | BU / GN | 4103 | AUTOSAR CAN Bus [+] 9 Serial Data | I | - |
| 6 | 0.35 | WH / GN | 4102 | AUTOSAR CAN Bus [-] 9 Serial Data | I | - |
| 7 | 0.35 | WH / BU | 6311 | Cruise/ETC/TCC Brake Signal | I | - |
| 8 - 9 | - | - | - | Not Occupied | - | - |
| 10 | 0.35 | WH / GN | 4102 | AUTOSAR CAN Bus [-] 9 Serial Data | I | - |
| 11 | 0.35 | BU / GN | 4103 | AUTOSAR CAN Bus [+] 9 Serial Data | I | - |
| 12 - 20 | - | - | - | Not Occupied | - | - |
| 21 | 0.35 | VT / GY | 1303 | Liftgate Ajar Switch Signal 1 | I | TB4 |
| 22 | 0.75 | RD / VT | 4040 | Battery Positive Voltage | II | - |
| 23 | 0.75 | BK / WH | 1251 | Signal Ground | II | - |
| 24 | 0.75 | RD / BU | 7640 | Battery Positive Voltage | II | - |
| 25 | 0.75 | BK / WH | 1251 | Signal Ground | II | - |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.