Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2025EQUINOX EV RS, AWDREPAIR AND DIAGNOSISSUSPENSIONWHEEL ALIGNMENTSPECIFICATIONSFASTENER SPECIFICATIONS
2025 Chevrolet Equinox EV RS, AWD
Fastener Specifications
2025 Chevrolet Equinox EV RS, AWDSECTION Fastener Specifications
NOTE:
Callout items in the following chart represent components shown in graphic above.
Rear Suspension Adjust Link Bolt
| Callout | Component Name [Component Quantity] | Single Use Fastener/Component | Thread Locking Adhesive Required | Specification | Procedure |
|---|---|---|---|---|---|
| Metric (English) | |||||
| 1 | Rear Suspension Link Adjust Bolt | - | - | - | Rear Suspension Adjust Link Replacement |
| 2 | Rear Suspension Adjust Link Nut | - | - | First Pass: 100 N.m (74 lb ft) Final Pass: 30 - 45 degrees |
Rear Toe Adjustment |
NOTE:
Callout items in the following chart represent components shown in graphic above.
Rear Suspension Lower Control Arm Inner Bolt
| Callout | Component Name [Component Quantity] | Single Use Fastener/Component | Thread Locking Adhesive Required | Specification | Procedure |
|---|---|---|---|---|---|
| Metric (English) | |||||
| 1 | Rear Suspension Lower Control Arm Inner Bolt | - | - | - | Rear Suspension Lower Control Arm Replacement |
| 2 | Rear Suspension Lower Control Arm Inner Nut | - | - | First Pass: 240 N.m (177 lb ft) Final Pass: 45 - 60 degrees |
Rear Camber Adjustment |
NOTE:
Callout items in the following chart represent components shown in graphic above.
Steering Knuckle
| Callout | Component Name [Component Quantity] | Single Use Fastener/Component | Thread Locking Adhesive Required | Specification | Procedure |
|---|---|---|---|---|---|
| Metric (English) | |||||
| 1 | Steering Knuckle Nut [2x] | - | - | First Pass: 160 N.m (118 lb ft) Final Pass: 30 - 45 degrees |
Front Camber Adjustment |
| 2 | Steering Knuckle Bolt [2x] | - | - | - | Steering Knuckle Replacement |
NOTE:
Callout items in the following chart represent components shown in graphic above.
Steering Linkage Inner Tie Rod Nut
| Callout | Component Name [Component Quantity] | Single Use Fastener/Component | Thread Locking Adhesive Required | Specification | Procedure |
|---|---|---|---|---|---|
| Metric (English) | |||||
| 1 | Steering Linkage Inner Tie Rod Nut | - | - | 75 N.m (55 lb ft) | Wheel Alignment - Steering Wheel Angle and/or Front Toe Adjustment |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.