Fastener Specifications

2025 Chevrolet Equinox EV LT, AWDSECTION Fastener Specifications
GM6387316Courtesy of GENERAL MOTORS COMPANY
NOTE: Callout items in the following chart represent components shown in graphic above.
Automatic Transmission Case and Associated Parts

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure Link
Metric (English)
1 Output Shaft Seal [2x] Yes - - Output Shaft Replacement - Left Side 
Output Shaft Replacement - Right Side 
2 Output Shaft Seal Dust Shield [2x] Yes - - Front Wheel Drive Shaft Oil Seal Replacement - Left Side 
Front Wheel Drive Shaft Oil Seal Replacement - Right Side 
3 Front Wheel Drive Shaft Oil Seal [2x] Yes - - Front Wheel Drive Shaft Oil Seal Replacement - Left Side 
Front Wheel Drive Shaft Oil Seal Replacement - Right Side 
4 Automatic Transmission Fluid Temperature Sensor Yes - 9 N.m (80 lb in) Automatic Transmission Fluid Temperature Sensor Replacement 
5 Transmission Fluid Drain Plug [2x] - - 19 N.m (14 lb ft) Transmission Fluid Drain and Fill 
6 Automatic Transmission Differential Carrier Bearing Retaining Ring Yes - - Output Shaft Replacement - Left Side 
GM6413190Courtesy of GENERAL MOTORS COMPANY
NOTE: Callout items in the following chart represent components shown in graphic above.
Battery Positive and Negative Cable

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure Link
Metric (English)
1 Battery Positive and Negative Cable Bracket Nut - - 9 N.m (80 lb in) Rear Electric Drive Transmission Module Replacement 
GM6413192Courtesy of GENERAL MOTORS COMPANY
NOTE: Callout items in the following chart represent components shown in graphic above.
High Voltage Battery Ground Bracket

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure Link
Metric (English)
1 High Voltage Battery Ground Bracket Bolt [2x] - - 22 N.m (16 lb ft) Rear Electric Drive Transmission Module Replacement 
GM6374122Courtesy of GENERAL MOTORS COMPANY
NOTE: Callout items in the following chart represent components shown in graphic above.
Rear Drive Motor Mount Bolt

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure Link
Metric (English)
1 Rear Drive Motor Mount Bolt - M12 x 101.6 Yes - First Pass: 100 N.m (74 lb ft)
Final Pass: 40 - 55 degrees
Rear Electric Drive Transmission Module Replacement 
GM6385633Courtesy of GENERAL MOTORS COMPANY
NOTE: Callout items in the following chart represent components shown in graphic above.
Rear Drive Motor Rear Mount Bolt

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure Link
Metric (English)
1 Rear Drive Motor Rear Mount Bolt - M14 x 113.43 [2x] - - First Pass: 100 N.m (74 lb ft) Rear Electric Drive Transmission Module Replacement 
GM6385616Courtesy of GENERAL MOTORS COMPANY
NOTE: Callout items in the following chart represent components shown in graphic above.
Underbody Rear Air Deflector Bracket Fasteners

Callout Component Name [Component Quantity] Single Use Fastener/Component Thread Locking Adhesive Required Specification Procedure Link
Metric (English)
1 Underbody Rear Air Deflector Bracket Bolt - M6 x 23 [2x] - - 9 N.m (80 lb in) Rear Electric Drive Transmission Module Replacement 
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • You smell fuel, burning insulation, or see smoke.
  • Brakes feel soft, pull hard to one side, or make grinding noises.
  • The engine overheats, stalls repeatedly, or misfires under load.
  • You are missing required tools, torque specs, or safe lifting equipment.
  • You are not confident in the next step or safety outcome.