Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Installation Procedure
Lighting Control Module (1) - Install
- Connect the electrical connector.
Radio (1) @ Radio Bracket (2) - Install
- Ensure that the retaining tabs are fully secured.
- NOTE:
Some components not shown for graphic clarity.
Radio Assembly (2) - Install
- Radio Bracket Bolt (1) - Install and tighten [3x] - Fastener Specifications
- Connect the electrical connector.
Electrical Connector (2) - Connect
- Instrument Panel Lower Trim Panel (1) - Install
Retainer (3) - Install [2x]
- Electrical Connector (2) - Install
- Wiring Harness Bracket Bolt (1) - Install and tighten [2x] - Fastener Specifications
Instrument Panel Lower Trim Panel Bolt (1) - Install and tighten [6x] - Fastener Specifications
Instrument Panel Lower Trim Panel Bolt (1) - Install and tighten [6x] - Fastener Specifications
Instrument Panel Lower Trim Panel Bolt (1) - Install and tighten [11x] - Fastener Specifications
Instrument Panel Compartment (1) - Install
- Push the sides of instrument panel compartment (1) to allow the door to go past the stops and engage the retainers.
Push the right side of instrument compartment panel (1), secure the instrument panel compartment support panel (2) to the instrument panel compartment (1).
- Connect the instrument panel compartment door dampener to the instrument panel compartment (1).
- Instrument Panel Compartment (1) - Close
Floor Front Air Outlet Duct - Left Side (1) - Install
Floor Front Air Outlet Duct Retainer (1) - Install
Instrument Panel Lower Trim Panel Insulator (2) - Install
- Instrument Panel Lower Trim Panel Insulator Retainer (1) - Install [3x]
Instrument Panel Lower Trim Panel Insulator (3) - Install
- Instrument Panel Lower Trim Panel Insulator Retainer (2) - Install [2x]
- Instrument Panel Lower Trim Panel Insulator Bolt (1) - Install and tighten [2x] - Fastener Specifications
Electrical Connector (1) - Connect
Instrument Panel Knee Bolster (2) - Install
- Instrument Panel Knee Bolster Bolt (1) - Install and tighten [4x] - Fastener Specifications
Instrument Panel Trim Pad (3) - Install
- { If equipped } Electrical Connector (2) - Connect
- Instrument Panel Trim Pad Bolt (1) - Install and tighten - Fastener Specifications
Instrument Panel Outer Trim Cover - Left Side (1) - Install
Instrument Panel Fuse Block Access Hole Cover (2) - Install
- Instrument Panel Knee Bolster Bolt (1) - Install and tighten - Fastener Specifications
Hood Primary Latch Release Cable Handle (1) - Install
Connect the electrical connector.
- Heater and Air Conditioning User Interface Control (2) - Install
- Heater and Air Conditioning User Interface Control Bolt (1) - Install and tighten [2x] - Fastener Specifications
Instrument Panel Trim Pad (4) - Install
- { If equipped } Electrical Connector (3) - Connect
- { If equipped } Electrical Connector (2) - Connect
- Instrument Panel Trim Pad Bolt (1) - Install and tighten [2x] - Fastener Specifications
Instrument Panel Outer Trim Cover - Right Side (1) - Install
Connect the electrical connectors.
- Radio Control (2) - Install
- Radio Control Bolt (1) - Install and tighten [4x] - Fastener Specifications
Connect the electrical connectors.
- Instrument Panel Cluster Control Module (2) - Install
- Instrument Cluster Bolt (1) - Install and tighten [4x] - Fastener Specifications
Instrument Panel Upper Trim Panel Cover (1) - Install
Connect the electrical connectors.
- Front Floor Console - Install - Front Floor Console Removal and Installation
- Perform the necessary programming and setup procedure: Control Module References
Refer to Fastener Caution .
NO RELATED
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.