Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2012CORVETTE V8-6.2L SCREPAIR AND DIAGNOSISTRANSMISSION AND DRIVETRAINDIFFERENTIAL ASSEMBLYLOCATIONS
2012 Chevrolet Corvette V8-6.2L SC
Differential Assembly: Locations
2012 Chevrolet Corvette V8-6.2L SCSECTION Locations
Rear Axle Disassembled Views
Differential Carrier and Case Assembly
1 - Output Shaft Oil Seal - Left
2 - Bolt
3 - Cover - Left
4 - Bushing
5 - O-Ring
6 - Oil Trough
7 - Dowel
8 - Magnet
9 - Carrier
10 - Vent
11 - O-Ring
12 - Dowel
13 - O-Ring
14 - Cover - Right
15 - Bolt
16 - Output Shaft Oil Seal - Right
17 - Differential Case Assembly
18 - Bolt
19 - Ring Gear
20 - Shim
21 - Bearing Cup
22 - Bearing
23 - Bolt
24 - Differential Case - Right
25 - Cross Pin
26 - Clutch Pack - Right
27 - Output Shaft to Drive Shaft Retaining Ring
28 - Gear and Output Shaft - Right
29 - Side Gears
30 - Side Gear Washers
31 - Gear - Left
32 - C-Clip - Some Models
32 - C-Clip - Some Models
33 - Output Shaft - Left
34 - Output Shaft to Drive Shaft Retaining Ring
35 - Clutch Pack - Left
36 - Differential Case - Left
37 - Bearing
38 - Bearing Cup
39 - Shim
40 - Quick Connect - Some Models
41 - Cover - Left - Some Models
42 - Output Shaft Gear - Right - Some Models
43 - Output Shaft - Right - Some Models
Drive Pinion Assembly
1 - Bolt - (2)
2 - Bolt
3 - Cover - Rear
4 - Gasket
5 - Nut
6 - Bolt
7 - Pinion Housing/Cage - with Bearings and Spacer
8 - Pinion - Some Models
8 - Pinion - Some Models
9 - Shims
10 - Carrier
11 - Bolt - Some Models
12 - Vehicle Speed Sensor - Some Models
13 - O-Ring - Some Models
14 - Transmission Stud - Case - Some Models
15 - Washer
16 - Drain Plug
17 - Washer
18 - Fill Plug
19 - Bearing
20 - Bearing Cup
21 - Pinion Housing/Cage
22 - Spacer
23 - Bearing Cup
24 - Bearing
25 - Pump Outlet Pipe - Some Models
26 - Pipe Clip - Some Models
27 - Quick Connect - Some Models
27 - Quick Connect - Some Models
28 - Rear Axle Cooler - Some Models
29 - Cooler Bolt - Some Models
30 - Rear Axle Pump - Some Models
31 - Pump Inlet Pipe - Some Models
32 - Quick Connect - Lower Cooler Adapter Nut - Some Models
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.