Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2010HHR L4-2.2LREPAIR AND DIAGNOSISPOWER AND GROUND DISTRIBUTIONAUXILIARY POWER OUTLET
2010 Chevrolet HHR L4-2.2L
Auxiliary Power Outlet
2010 Chevrolet HHR L4-2.2LSECTION Auxiliary Power Outlet
Description and Operation
Testing and Inspection
Service and Repair
Diagrams- Diagram Information and Instructions
- Diagnostic Aids
- Arrows and Symbols
- Decimal and Metric Equivalents
- General Electrical Diagnostic Procedures
- Checking Aftermarket Accessories
- Circuit Testing
- Circuit Testing
- Troubleshooting with a Test Lamp
- Testing for a Short to Voltage
- Inducing Intermittent Fault Conditions
- Measuring Frequency
- Measuring Voltage
- Measuring Voltage Drop
- Probing Electrical Connectors
- Scan Tool Snapshot Procedure
- Testing for Continuity
- Testing for Electrical Intermittents
- Testing for Intermittent Conditions and Poor Connections
- Testing for Short to Ground
- Troubleshooting with a Digital Multimeter
- Using Connector Test Adapters
- Using Fused Jumper Wires
- Connector Repairs
- AFL/EPC Connectors
- Bosch Connectors (BSK)
- Bosch Connectors (ECM)
- Bosch Connectors (0.64)
- Bosch Connectors (2.8 JPT)
- Connector Position Assurance Locks
- Connector Repairs
- Delphi Connectors (Micro .64)
- Delphi Connectors (Micro-Pack 100W)
- Delphi Connectors (Pull To Seat)
- Delphi Connectors (Push To Seat)
- Delphi Connectors (Weather Pack)
- Delphi Connectors (12-Way)
- FCI Connectors
- JST Connectors
- Kostal Connectors (Glow Plug Control Module)
- Kostal Connectors (Transmission)
- Molex Connectors
- Tyco/AMP Connectors (CM 42-Way)
- Tyco/AMP Connectors (43-Way)
- Tyco/AMP Connectors (Door Module)
- Tyco/AMP Connectors (102-Way Inline)
- Tyco/AMP Connectors (Seat)
- Tyco/AMP Connectors (SIR)
- Repairing Connector Terminals
- Sumitomo Connectors
- Terminal Position Assurance Locks
- Tyco/AMP Connectors (Sensor)
- Tyco/AMP Connectors (0.25 Cap)
- Yazaki Connectors (2-Way)
- Yazaki Connectors (16-Way)
- Wiring Repairs
- Circuit Protection - Circuit Breakers
- Circuit Protection - Fuses
- Circuit Protection - Fusible Links
- Flat Wire Repairs
- GMLAN Wiring Repairs
- Heated Oxygen Sensor Wiring Repairs
- High Temperature Wiring Repairs
- Repairing Damaged Wire Insulation
- SIR/SRS Wiring Repairs
- Splicing Copper Wire Using Splice Sleeves
- Splicing Inline Harness Diodes
- Splicing Twisted or Shielded Cable
- Wiring Repairs
- US English/Metric Conversion
- Connector Views
- Electrical Diagrams
Tools and Equipment
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.