Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2006MALIBU V6-3.9L VIN 1REPAIR AND DIAGNOSISBODY AND FRAMELOCKSPOWER LOCKSPOWER DOOR LOCK CONTROL MODULETECHNICAL SERVICE BULLETINSBODY - REVISED POWER DOOR LOCK RECEIVER REPLACEMENT
2006 Chevrolet Malibu V6-3.9L VIN 1
Body - Revised Power Door Lock Receiver Replacement
2006 Chevrolet Malibu V6-3.9L VIN 1SECTION Body - Revised Power Door Lock Receiver Replacement
Bulletin No.: 05-08-52-004
Date: December 14, 2005
SERVICE MANUAL UPDATE
Subject:
Revised Remote Control Door Lock Receiver Replacement (Sedan)
Models:
2005-2006 Chevrolet Malibu (Sedan)
This bulletin is being issued to revise the Remote Control Door Lock Receiver Replacement (Sedan) procedure in the Keyless Entry sub-section of the Service Manual. Please replace the current information in the Service Manual with the following information.
The following information has been updated within SI. If you are using a paper version of this Service Manual, please make a reference to this bulletin on the affected page.
When replacing a remote control door lock receiver, it is not necessary to remove the rear window shelf panel. Access the receiver through the opening in the rear window (sheet metal) panel.
Remote Control Door Lock Receiver Replacement (Sedan)
Removal Procedure
1. Open the rear compartment lid.
2. Working through the access hole, disconnect the electrical connectors from the receiver.
3. Working through the access hole, remove the receiver from the vehicle.
Installation Procedure
1. Install the receiver to the vehicle.
2. Connect the electrical connectors to the receiver.
3. The transmitter will need to be programmed after replacement. Refer to Control Module References for programming and setup information.
Disclaimer
Date: December 14, 2005
SERVICE MANUAL UPDATE
Subject:
Revised Remote Control Door Lock Receiver Replacement (Sedan)
Models:
2005-2006 Chevrolet Malibu (Sedan)
This bulletin is being issued to revise the Remote Control Door Lock Receiver Replacement (Sedan) procedure in the Keyless Entry sub-section of the Service Manual. Please replace the current information in the Service Manual with the following information.
The following information has been updated within SI. If you are using a paper version of this Service Manual, please make a reference to this bulletin on the affected page.
When replacing a remote control door lock receiver, it is not necessary to remove the rear window shelf panel. Access the receiver through the opening in the rear window (sheet metal) panel.
Remote Control Door Lock Receiver Replacement (Sedan)
Removal Procedure
1. Open the rear compartment lid.
2. Working through the access hole, disconnect the electrical connectors from the receiver.
3. Working through the access hole, remove the receiver from the vehicle.
Installation Procedure
1. Install the receiver to the vehicle.
2. Connect the electrical connectors to the receiver.
3. The transmitter will need to be programmed after replacement. Refer to Control Module References for programming and setup information.
Disclaimer
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.