Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2006IMPALA V6-3.5L VIN K FLEX FUELREPAIR AND DIAGNOSISDIAGRAMSEXPLODED VIEWSSTEERING COLUMNSTEERING COLUMN DISASSEMBLED VIEW (COLUMN SHIFT)
2006 Chevrolet Impala V6-3.5L VIN K Flex Fuel
Steering Column Disassembled View (Column Shift)
2006 Chevrolet Impala V6-3.5L VIN K Flex FuelSECTION Steering Column Disassembled View (Column Shift)
Steering Column Disassembled View (Column Shift)
Tilt Steering Column, Column Shift:
1 - Upper Trim Cover
2 - Lower Trim Cover
3 - Shift Lever Assembly
4 - Shift Lever Screw
5 - Shift Lever Seal
6 - Flanged Prevailing Torque Nut
7 - Retaining Ring
8 - SIR Coil
9 - Wave Washer
10 - Bearing Retainer
11 - Shaft Lock Shield Assembly
12 - Turn Signal Cancel Cam Assembly
13 - Upper Bearing Spring
14 - Upper Bearing Inner Race Seat
15 - Inner Race
16 - Pan Head Tapping Screws
17 - TORX Head Screw
18 - Ignition Lock Cylinder Case Assembly
19 - Steering Column Lock Cylinder Set
20 - Pan Head Tapping Screw
21 - Tapping Screws
22 - Ignition Switch Assembly
23 - Steering Column Tilt Head Housing Assembly
24 - Lock Bolt Spring
25 - Lock Bolt Assembly
26 - Spring Guide
27 - Tilt Spring
28 - TORX Head Screw
29 - Wire Harness Strap
30 - Trim Cover Protector
31 - Tilt Knob
32 - TORX Head Screws
33 - Pan Head Tapping Screws
34 - Turn Signal and Multifunction Switch Assembly
35 - Wire Harness Straps
36 - Position Assurance Connector
37 - Race and Upper Shaft Assembly
38 - Joint Preload Spring
39 - Centering Sphere
40 - Lower Steering Shaft Assembly
41 - Linear Shift Assembly
42 - Shift Lever Clevis
43 - Flat Head 6-Lobed Soc Tap Screws
44 - Cable Shift Cam Assembly
45 - Ball and Actuator Assembly
46 - Cam Bushing
47 - Hexagon Flange Head Bolts
48 - Gear Shift Lever Assembly Support Bracket
49 - Oval Head 6-Lobed Soc Tap Screws
50 - Park Lock Cable System
51 - TORX Head Screws
52 - Pivot Pins
53 - Steering Column Support Assembly
54 - Steering Column Jacket Assembly
55 - Automatic Transmission Shift Lock Control
56 - Adapter and Bearing Assembly
57 - Lower Bearing Seat
58 - Lower Bearing Spring
59 - Lower Spring Retainer
60 - Retainer
61 - Steering Shaft Seal
62 - Intermediate Steering Shaft Assembly
63 - Pinch Bolt
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.