Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2004MONTE CARLO V6-3.4L VIN EREPAIR AND DIAGNOSISPOWERTRAIN MANAGEMENTCOMPUTERS AND CONTROL SYSTEMSTESTING AND INSPECTIONSCAN TOOL TESTING AND PROCEDURESSCAN TOOL DATA, NORMAL VALUES AND DEFINITIONSSCAN TOOL DATA DEFINITIONS - ANTITHEFT SYSTEMS
2004 Chevrolet Monte Carlo V6-3.4L VIN E
Scan Tool Data Definitions - Antitheft Systems
2004 Chevrolet Monte Carlo V6-3.4L VIN ESECTION Scan Tool Data Definitions - Antitheft Systems
SCAN TOOL DATA DEFINITIONS
Lockout Timer Status: The duration of time the system remains in tamper mode The VTD system will disable sampling of the key code for 10 minutes when a tamper is detected.
Auto-Learn Timer Status: The duration of time the system remains in the re-learn wait mode.
Seed & Key Timer Status: The scan tool displays the time in seconds used by the BCM to learn a valid code from the passlock sensor. The learn procedure consists of 3 separate periods.
Passlock Data Voltage: Displays the voltage data from the Passlock Sensor to the BCM. The BCM determines if the data received is valid or invalid.
Security Lamp State: Indicates the state of the SECURITY indicator either on, off or flashing.
His DTC Cyc. Counts.: Displays the number of key cycles that have occurred in order to clear history DTCs.
PCM/VCM in VTD Fail Enable: The scan tool displays which state the Powertrain Control Module (PCM) is currently in for the Vehicle Theft Deterrent (VTD).
VTD Fuel Disable: The scan tool displays the state of which the fuel delivery system is in.
VTD Auto Learn Timer: The scan tool displays which state the learn timer for the VTD is currently in.
VTD Fuel Disable Until Ign. OFF: The scan tool display the state of which the fuel delivery system is in according to the ignition switch position.
Lockout Timer Status: The duration of time the system remains in tamper mode The VTD system will disable sampling of the key code for 10 minutes when a tamper is detected.
Auto-Learn Timer Status: The duration of time the system remains in the re-learn wait mode.
Seed & Key Timer Status: The scan tool displays the time in seconds used by the BCM to learn a valid code from the passlock sensor. The learn procedure consists of 3 separate periods.
Passlock Data Voltage: Displays the voltage data from the Passlock Sensor to the BCM. The BCM determines if the data received is valid or invalid.
Security Lamp State: Indicates the state of the SECURITY indicator either on, off or flashing.
His DTC Cyc. Counts.: Displays the number of key cycles that have occurred in order to clear history DTCs.
PCM/VCM in VTD Fail Enable: The scan tool displays which state the Powertrain Control Module (PCM) is currently in for the Vehicle Theft Deterrent (VTD).
VTD Fuel Disable: The scan tool displays the state of which the fuel delivery system is in.
VTD Auto Learn Timer: The scan tool displays which state the learn timer for the VTD is currently in.
VTD Fuel Disable Until Ign. OFF: The scan tool display the state of which the fuel delivery system is in according to the ignition switch position.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.