Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2004MONTE CARLO V6-3.4L VIN EREPAIR AND DIAGNOSISHEATING AND AIR CONDITIONINGTESTING AND INSPECTIONSCAN TOOL TESTING AND PROCEDURESSCAN TOOL DATA DEFINITIONS
2004 Chevrolet Monte Carlo V6-3.4L VIN E
Scan Tool Data Definitions
2004 Chevrolet Monte Carlo V6-3.4L VIN ESECTION Scan Tool Data Definitions
SCAN TOOL DATA DEFINITIONS
The HVAC Scan Tool Data Definitions contains a brief description of all HVAC related parameters available on the scan tool. The list is in alphabetical order. A given parameter may appear in any one of the data lists. In some cases, the parameter may appear more than once or in more than one data list in order to group certain related parameters together.
BCM - Inputs - A/C Switch: The scan tool displays Active or Inactive. Displays the state of the A/C request signal circuit from the HVAC control assembly to the BCM.
PCM - A/C Relay Command: The scan tool displays On or Off. On is displayed when the PCM has energized the A/C compressor clutch relay.
PCM - Engine Data 2 - A/C High Side Pressure Sensor: The scan tool displays -103 to +3119 kPa, (-14 to +452 psi). This parameter represents the A/C refrigerant pressure sensor voltage signal converted to pressure.
PCM - Engine Data 2 - A/C High Side Pressure Sensor: The scan tool displays 0 to 5 volts. The output of the A/C refrigerant pressure sensor.
PCM - Engine Data 2 - A/C Off For WOT: The scan tool displays Yes or No. Yes indicates that the PCM has disabled the A/C compressor because the TP sensor signal is at wide open throttle.
PCM - Engine Data 2 - A/C Pressure Disable: The scan tool displays Yes or No. Yes is displayed when the system pressure exceeds 2968 kPa (430 psi).
PCM - Engine Data 2 - A/C Request Signal: The scan tool displays Yes or No. Yes is displayed when the PCM receives an A/C request signal from the BCM.
PCM - Output Driver Data - A/C Relay Circuit Status: The scan tool displays OK or Fault. Fault is displayed when an open or short is detected in the A/C compressor clutch relay ground circuit.
The HVAC Scan Tool Data Definitions contains a brief description of all HVAC related parameters available on the scan tool. The list is in alphabetical order. A given parameter may appear in any one of the data lists. In some cases, the parameter may appear more than once or in more than one data list in order to group certain related parameters together.
BCM - Inputs - A/C Switch: The scan tool displays Active or Inactive. Displays the state of the A/C request signal circuit from the HVAC control assembly to the BCM.
PCM - A/C Relay Command: The scan tool displays On or Off. On is displayed when the PCM has energized the A/C compressor clutch relay.
PCM - Engine Data 2 - A/C High Side Pressure Sensor: The scan tool displays -103 to +3119 kPa, (-14 to +452 psi). This parameter represents the A/C refrigerant pressure sensor voltage signal converted to pressure.
PCM - Engine Data 2 - A/C High Side Pressure Sensor: The scan tool displays 0 to 5 volts. The output of the A/C refrigerant pressure sensor.
PCM - Engine Data 2 - A/C Off For WOT: The scan tool displays Yes or No. Yes indicates that the PCM has disabled the A/C compressor because the TP sensor signal is at wide open throttle.
PCM - Engine Data 2 - A/C Pressure Disable: The scan tool displays Yes or No. Yes is displayed when the system pressure exceeds 2968 kPa (430 psi).
PCM - Engine Data 2 - A/C Request Signal: The scan tool displays Yes or No. Yes is displayed when the PCM receives an A/C request signal from the BCM.
PCM - Output Driver Data - A/C Relay Circuit Status: The scan tool displays OK or Fault. Fault is displayed when an open or short is detected in the A/C compressor clutch relay ground circuit.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.