Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2003MALIBU V6-3.1L VIN JREPAIR AND DIAGNOSISCRUISE CONTROLCRUISE CONTROL MODULESERVICE AND REPAIR
2003 Chevrolet Malibu V6-3.1L VIN J
Cruise Control Module: Service and Repair
2003 Chevrolet Malibu V6-3.1L VIN JSECTION Service and Repair
CRUISE CONTROL MODULE REPLACEMENT
REMOVAL PROCEDURE
1. Open the hood.
2. Disconnect the cruise control cable tab (5) from the throttle body cam (6). Rotate the cam (6)to 1/4 open throttle in order to release the tab (5).
3. In order to release the cable (4), push the locating fitting inward and pull the unit free from he throttle bracket (1).
4. Remove the cruise control cable from the module by turning the cable assembly 1/4 turn counterclockwise.
5. Remove the cable from the ribbon.
6. Disconnect the electrical connector from the module assembly.
7. Unclip the hinged retaining strap from the bracket at the top of the module.
8. Remove the module from the mounting bracket.
INSTALLATION PROCEDURE
1. Install the module assembly to the mounting bracket.
2. Connect the electrical connector to the module.
3. Connect the cruise control cable to the module ribbon.
4. Install the cruise control cable to the module assembly by turning the cable assembly 1/4 turn clockwise.
5. Install the cruise control cable tab (5) to the throttle body cam (6).
6. Align the cruise control cable fitting to the throttle body bracket (1). Snap the fitting into place. Ensure that the fitting is retained.
7. Close the hood.
8. Perform A Diagnostic System Check.
REMOVAL PROCEDURE
1. Open the hood.
2. Disconnect the cruise control cable tab (5) from the throttle body cam (6). Rotate the cam (6)to 1/4 open throttle in order to release the tab (5).
3. In order to release the cable (4), push the locating fitting inward and pull the unit free from he throttle bracket (1).
4. Remove the cruise control cable from the module by turning the cable assembly 1/4 turn counterclockwise.
5. Remove the cable from the ribbon.
6. Disconnect the electrical connector from the module assembly.
7. Unclip the hinged retaining strap from the bracket at the top of the module.
8. Remove the module from the mounting bracket.
INSTALLATION PROCEDURE
1. Install the module assembly to the mounting bracket.
2. Connect the electrical connector to the module.
3. Connect the cruise control cable to the module ribbon.
4. Install the cruise control cable to the module assembly by turning the cable assembly 1/4 turn clockwise.
5. Install the cruise control cable tab (5) to the throttle body cam (6).
6. Align the cruise control cable fitting to the throttle body bracket (1). Snap the fitting into place. Ensure that the fitting is retained.
7. Close the hood.
8. Perform A Diagnostic System Check.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.