Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2002MONTE CARLO V6-3.8L VIN KREPAIR AND DIAGNOSISTESTING AND INSPECTIONPROGRAMMING AND RELEARNINGSERVICE PROGRAMMING SYSTEM (SPS) - METHODS
2002 Chevrolet Monte Carlo V6-3.8L VIN K
Service Programming System (SPS) - Methods
2002 Chevrolet Monte Carlo V6-3.8L VIN KSECTION Service Programming System (SPS) - Methods
The 4 methods of programming a control module and the proper tools for each method are as follows:
^ Remote Programming:
- The Tech 2 or other scan tool, Techline Terminal or a personal computer equipped with General Motors Corporation authorized programming software-The Tech 2 or other scan tool is used as an interface between the vehicle and the Techline Terminal or a personal computer.
- The control module is installed in the vehicle
^ Pass Thru Programming:
- The Tech 2 or other scan tool, Techline Terminal or a personal computer equipped with General Motors Corporation authorized programming software-The Tech 2 or other scan tool is used as an interface between the vehicle and the Techline Terminal or a personal computer.
- The control module is installed in the vehicle.
^ Off-Board Remote Programming, vehicle NOT available:
- The Tech 2 or other scan tool, Off-board Programming Adapter (OBPA), Techline Terminal or a personal computer equipped with General Motors Corporation authorized programming software-The Tech 2 or other scan tool is used as an interface between the vehicle and the Techline Terminal or a personal computer.
- The control module is NOT installed in a vehicle
^ Off-Board Pass Thru Programming
- The Tech 2 or other scan tool, off-board programming adapter (OBPA), Techline Terminal or a personal computer equipped with General Motors Corporation authorized programming software-The Tech 2 or other scan tool is used as an interface between the vehicle and the Techline Terminal or a personal computer.
- The control module is NOT installed in a vehicle
^ Remote Programming:
- The Tech 2 or other scan tool, Techline Terminal or a personal computer equipped with General Motors Corporation authorized programming software-The Tech 2 or other scan tool is used as an interface between the vehicle and the Techline Terminal or a personal computer.
- The control module is installed in the vehicle
^ Pass Thru Programming:
- The Tech 2 or other scan tool, Techline Terminal or a personal computer equipped with General Motors Corporation authorized programming software-The Tech 2 or other scan tool is used as an interface between the vehicle and the Techline Terminal or a personal computer.
- The control module is installed in the vehicle.
^ Off-Board Remote Programming, vehicle NOT available:
- The Tech 2 or other scan tool, Off-board Programming Adapter (OBPA), Techline Terminal or a personal computer equipped with General Motors Corporation authorized programming software-The Tech 2 or other scan tool is used as an interface between the vehicle and the Techline Terminal or a personal computer.
- The control module is NOT installed in a vehicle
^ Off-Board Pass Thru Programming
- The Tech 2 or other scan tool, off-board programming adapter (OBPA), Techline Terminal or a personal computer equipped with General Motors Corporation authorized programming software-The Tech 2 or other scan tool is used as an interface between the vehicle and the Techline Terminal or a personal computer.
- The control module is NOT installed in a vehicle
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.