Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2002EXPRESS 1 TON VAN V8-8.1L VIN GREPAIR AND DIAGNOSISRESTRAINTS AND SAFETY SYSTEMSAIR BAG SYSTEMSAIR BAGSERVICE AND REPAIRINFLATOR MODULE REPLACEMENTSTEERING WHEEL MODULE REPLACEMENT
2002 Chevrolet Express 1 Ton Van V8-8.1L VIN G
Steering Wheel Module Replacement
2002 Chevrolet Express 1 Ton Van V8-8.1L VIN GSECTION Steering Wheel Module Replacement
REMOVAL PROCEDURE
CAUTION: Refer to SIR Caution in Service Precautions.
1. Disable the SIR system. Refer to Air Bag(s) Arming and Disarming.
2. Turn the ignition switch to the ON position to unlock the steering wheel.
3. Turn the steering wheel 90 degrees so the side of the SIR module is at the 12 o'clock position in order to gain access to the hole behind the steering wheel.
4. Insert a screwdriver into the access hole and push the leaf spring to release the notched pin that retains the inflator module.
5. Turn the steering wheel 180 degrees to gain access to the remaining access hole.
6. Insert a screwdriver into the remaining access hole and push the leaf spring to release the notched pin that retains the inflator module.
7. Tilt the top of the inflator module rearward to gain access to the SIR wiring.
8. Disconnect the SIR lead wire from the clip on the inflator module.
9. Disconnect the SIR lead wire from the clip on the steering wheel.
10. Disconnect the connector position assurance (CPA) retainer.
11. Disconnect the electrical connector.
CAUTION: Refer to SIR Inflator Module Handling And Storage Caution in Service Precautions.
12. Remove the inflator module from the vehicle.
INSTALLATION PROCEDURE
1. Align the inflatable restraint module to the steering wheel.
CAUTION: Refer to SIR Inflator Module Handling And Storage Caution in Service Precautions.
2. Install the electrical connector.
3. Install the CPA retainer.
4. Install the SIR lead wire to the clip on the steering wheel.
5. Install the SIR lead wire to the clip on the inflator module.
6. Ensure that the wiring is not exposed or trapped between the inflatable restraint steering wheel module and the steering wheel.
7. Install the inflator module onto the steering wheel and press the module into the retaining tabs until the module is secured properly in all retaining locations.
8. Rotate the steering wheel back into the straight position.
9. Enable the SIR system. Refer to Air Bag(s) Arming and Disarming.
CAUTION: Refer to SIR Caution in Service Precautions.
1. Disable the SIR system. Refer to Air Bag(s) Arming and Disarming.
2. Turn the ignition switch to the ON position to unlock the steering wheel.
3. Turn the steering wheel 90 degrees so the side of the SIR module is at the 12 o'clock position in order to gain access to the hole behind the steering wheel.
4. Insert a screwdriver into the access hole and push the leaf spring to release the notched pin that retains the inflator module.
5. Turn the steering wheel 180 degrees to gain access to the remaining access hole.
6. Insert a screwdriver into the remaining access hole and push the leaf spring to release the notched pin that retains the inflator module.
7. Tilt the top of the inflator module rearward to gain access to the SIR wiring.
8. Disconnect the SIR lead wire from the clip on the inflator module.
9. Disconnect the SIR lead wire from the clip on the steering wheel.
10. Disconnect the connector position assurance (CPA) retainer.
11. Disconnect the electrical connector.
CAUTION: Refer to SIR Inflator Module Handling And Storage Caution in Service Precautions.
12. Remove the inflator module from the vehicle.
INSTALLATION PROCEDURE
1. Align the inflatable restraint module to the steering wheel.
CAUTION: Refer to SIR Inflator Module Handling And Storage Caution in Service Precautions.
2. Install the electrical connector.
3. Install the CPA retainer.
4. Install the SIR lead wire to the clip on the steering wheel.
5. Install the SIR lead wire to the clip on the inflator module.
6. Ensure that the wiring is not exposed or trapped between the inflatable restraint steering wheel module and the steering wheel.
7. Install the inflator module onto the steering wheel and press the module into the retaining tabs until the module is secured properly in all retaining locations.
8. Rotate the steering wheel back into the straight position.
9. Enable the SIR system. Refer to Air Bag(s) Arming and Disarming.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.