Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2001LUMINA V6-3.1L VIN JREPAIR AND DIAGNOSISPOWERTRAIN MANAGEMENTCOMPUTERS AND CONTROL SYSTEMSTESTING AND INSPECTIONCOMPONENT TESTS AND GENERAL DIAGNOSTICSEVAP CONTROL SYSTEM DIAGNOSIS (GENERAL TABLE)
2001 Chevrolet Lumina V6-3.1L VIN J
EVAP Control System Diagnosis (General Table)
2001 Chevrolet Lumina V6-3.1L VIN JSECTION EVAP Control System Diagnosis (General Table)
Refer to EVAP System Overview.
SYSTEM DESCRIPTION
The EVAP canister purge valve allows manifold vacuum to purge the canister. The Powertrain Control Module (PCM) supplies a Ground to energize the purge valve (purge ON). The EVAP purge valve control is Pulse Width Modulated (PWM) or Turned ON and OFF several times a second. The duty cycle (pulse width) is determined by engine operating conditions including load, throttle position, coolant temperature and ambient temperature. The duty cycle is calculated by the PCM and the output is commanded when the appropriate conditions have been met.
The EVAP Vent valve is used to seal the EVAP system during diagnostic tests. The fuel tank pressure sensor is used to monitor vacuum in the system during the diagnostic tests.
A stuck closed EVAP canister purge valve, Stuck open EVAP vent valve, disconnected or damaged EVAP Purge line or vent hose, leaking fuel cap, or fill neck should set a DTC P0440. A small leak in the EVAP system should set a DTC P0442. An EVAP vent valve stuck closed, a restricted vent hose, or a blocked EVAP canister should set a DTC P0446. A continuous purge condition with no purge commanded by the PCM (EVAP purge valve stuck open or leaking) should set a DTC P1441. Refer to the DTC tables for further diagnostic procedures regarding the EVAP system.
The EVAP system includes the following components:
^ The EVAP canister.
^ The EVAP canister purge valve.
^ The EVAP vent valve.
^ The EVAP vapor pipes.
^ The EVAP purge pipes..
^ The EVAP fresh air vent hose.
^ The fuel tank.
^ The fuel pipes and hoses.
^ The fuel fill cap.
^ The fuel fill pipe.
DIAGNOSTIC AIDS
Check for the following conditions:
^ Cracked or punctured EVAP canister.
^ Damaged or disconnected source vacuum line, EVAP purge line, vent hose or fuel tank vapor line.
^ Poor connection at the PCM.
^ Inspect harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals. and poor terminal to wire connection.
^ Damaged harness. Inspect the wiring harness to the EVAP vent valve, the EVAP purge valve, and the fuel tank pressure sensor for an intermittent open or short circuit.
^ Kinked, pinched or plugged vacuum source, EVAP purge, or fuel tank vapor line. Verify that the lines are not restricted.
^ Carbon being released into the system.
Diagnostic Chart (Part 1 Of 2):
Diagnostic Chart (Part 2 Of 2):
SYSTEM DESCRIPTION
The EVAP canister purge valve allows manifold vacuum to purge the canister. The Powertrain Control Module (PCM) supplies a Ground to energize the purge valve (purge ON). The EVAP purge valve control is Pulse Width Modulated (PWM) or Turned ON and OFF several times a second. The duty cycle (pulse width) is determined by engine operating conditions including load, throttle position, coolant temperature and ambient temperature. The duty cycle is calculated by the PCM and the output is commanded when the appropriate conditions have been met.
The EVAP Vent valve is used to seal the EVAP system during diagnostic tests. The fuel tank pressure sensor is used to monitor vacuum in the system during the diagnostic tests.
A stuck closed EVAP canister purge valve, Stuck open EVAP vent valve, disconnected or damaged EVAP Purge line or vent hose, leaking fuel cap, or fill neck should set a DTC P0440. A small leak in the EVAP system should set a DTC P0442. An EVAP vent valve stuck closed, a restricted vent hose, or a blocked EVAP canister should set a DTC P0446. A continuous purge condition with no purge commanded by the PCM (EVAP purge valve stuck open or leaking) should set a DTC P1441. Refer to the DTC tables for further diagnostic procedures regarding the EVAP system.
The EVAP system includes the following components:
^ The EVAP canister.
^ The EVAP canister purge valve.
^ The EVAP vent valve.
^ The EVAP vapor pipes.
^ The EVAP purge pipes..
^ The EVAP fresh air vent hose.
^ The fuel tank.
^ The fuel pipes and hoses.
^ The fuel fill cap.
^ The fuel fill pipe.
DIAGNOSTIC AIDS
Check for the following conditions:
^ Cracked or punctured EVAP canister.
^ Damaged or disconnected source vacuum line, EVAP purge line, vent hose or fuel tank vapor line.
^ Poor connection at the PCM.
^ Inspect harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals. and poor terminal to wire connection.
^ Damaged harness. Inspect the wiring harness to the EVAP vent valve, the EVAP purge valve, and the fuel tank pressure sensor for an intermittent open or short circuit.
^ Kinked, pinched or plugged vacuum source, EVAP purge, or fuel tank vapor line. Verify that the lines are not restricted.
^ Carbon being released into the system.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.