Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2001EXPRESS 1/2 TON VAN V6-4.3L VIN WREPAIR AND DIAGNOSISRELAYS AND MODULESRELAYS AND MODULES - WINDOWS AND GLASSPOWER WINDOW CONTROL MODULESERVICE AND REPAIR
2001 Chevrolet Express 1/2 Ton Van V6-4.3L VIN W
Power Window Control Module: Service and Repair
2001 Chevrolet Express 1/2 Ton Van V6-4.3L VIN WSECTION Service and Repair
REMOVAL PROCEDURE
1. Remove the front door trim panel.
2. Remove the front door speaker.
3. Remove the front door water deflector.
4. Lower the window.
5. Remove the inner window sealing strip.
6. Remove the outer window sealing strip.
7. Remove the front and rear run channel from the door.
8. Remove the inside handle from the door.
9. Remove the lock rods from the front door module (1).
10. Remove the electrical harness from the front door module (1).
11. Remove the rivets (3), that retain the front door module (1) to the door, with an appropriate drill and drill bit.
12. Remove the front door module (1) from the vehicle.
INSTALLATION PROCEDURE
1. Install the front door module (1) to the vehicle.
2. Rivet (3) the front door module (1) to the door.
3. Install the electrical harness to the front door module (1).
4. Install the lock rods to the front door module.
5. Install the inside handle to the door.
6. Install the front and rear run channel to the door.
7. Install the inner window sealing strip.
8. Install the outer window sealing strip.
9. Install the front door water deflector.
10. Install the front door speaker.
11. Install the front door trim panel.
1. Remove the front door trim panel.
2. Remove the front door speaker.
3. Remove the front door water deflector.
4. Lower the window.
5. Remove the inner window sealing strip.
6. Remove the outer window sealing strip.
7. Remove the front and rear run channel from the door.
8. Remove the inside handle from the door.
9. Remove the lock rods from the front door module (1).
10. Remove the electrical harness from the front door module (1).
11. Remove the rivets (3), that retain the front door module (1) to the door, with an appropriate drill and drill bit.
12. Remove the front door module (1) from the vehicle.
INSTALLATION PROCEDURE
1. Install the front door module (1) to the vehicle.
2. Rivet (3) the front door module (1) to the door.
3. Install the electrical harness to the front door module (1).
4. Install the lock rods to the front door module.
5. Install the inside handle to the door.
6. Install the front and rear run channel to the door.
7. Install the inner window sealing strip.
8. Install the outer window sealing strip.
9. Install the front door water deflector.
10. Install the front door speaker.
11. Install the front door trim panel.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.