Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2001EXPRESS 1/2 TON VAN V6-4.3L VIN WREPAIR AND DIAGNOSISPOWERTRAIN MANAGEMENTCOMPUTERS AND CONTROL SYSTEMSCAMSHAFT POSITION SENSORSERVICE AND REPAIR
2001 Chevrolet Express 1/2 Ton Van V6-4.3L VIN W
Camshaft Position Sensor: Service and Repair
2001 Chevrolet Express 1/2 Ton Van V6-4.3L VIN WSECTION Service and Repair
CAMSHAFT POSITION (CMP) SENSOR REPLACEMENT
REMOVAL PROCEDURE
1. Remove the engine cover.
2. Disconnect the spark plug wires and ignition coil wire from the distributor.
3. Disconnect the Camshaft Position (CMP) sensor harness connector from the distributor.
4. Remove the distributor cap screws.
5. Remove the distributor cap.
6. Remove the rotor screws.
7. Remove the rotor.
8. Align the square slot in the reluctor wheel with the CMP sensor.
9. Remove the CMP screws.
10. Remove the CMP sensor.
INSTALLATION PROCEDURE
IMPORTANT: Do not use the old cap, CMP sensor, and rotor screws. Use the replacement screws that have been coated with a thread locking compound.
1. Insert the CMP sensor through the reluctor wheel slot.
NOTE: Refer to Fastener Notice in Service Precautions.
2. Install new CMP mounting screws.
Tighten
Tighten the bolts to 2.2 N.m (20 lb in).
3. Install the rotor onto the reluctor wheel.
4. Install new rotor screws.
Tighten
Tighten the screws to 2 N.m (18 lb in).
5. Install the distributor cap.
6. Install new distributor cap screws.
Tighten
Tighten the screws to 2.4 N.m (21 lb in).
7. Connect the CMP sensor harness connector.
8. Connect the spark plug wires and ignition coil wire.
9. Install the engine cover.
REMOVAL PROCEDURE
1. Remove the engine cover.
2. Disconnect the spark plug wires and ignition coil wire from the distributor.
3. Disconnect the Camshaft Position (CMP) sensor harness connector from the distributor.
4. Remove the distributor cap screws.
5. Remove the distributor cap.
6. Remove the rotor screws.
7. Remove the rotor.
8. Align the square slot in the reluctor wheel with the CMP sensor.
9. Remove the CMP screws.
10. Remove the CMP sensor.
INSTALLATION PROCEDURE
IMPORTANT: Do not use the old cap, CMP sensor, and rotor screws. Use the replacement screws that have been coated with a thread locking compound.
1. Insert the CMP sensor through the reluctor wheel slot.
NOTE: Refer to Fastener Notice in Service Precautions.
2. Install new CMP mounting screws.
Tighten
Tighten the bolts to 2.2 N.m (20 lb in).
3. Install the rotor onto the reluctor wheel.
4. Install new rotor screws.
Tighten
Tighten the screws to 2 N.m (18 lb in).
5. Install the distributor cap.
6. Install new distributor cap screws.
Tighten
Tighten the screws to 2.4 N.m (21 lb in).
7. Connect the CMP sensor harness connector.
8. Connect the spark plug wires and ignition coil wire.
9. Install the engine cover.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.