Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2000MALIBU V6-3.1L VIN JREPAIR AND DIAGNOSISSTARTING AND CHARGINGCHARGING SYSTEMALTERNATORSERVICE AND REPAIR
2000 Chevrolet Malibu V6-3.1L VIN J
Alternator: Service and Repair
2000 Chevrolet Malibu V6-3.1L VIN JSECTION Service and Repair
GENERATOR REPLACEMENT
The generator does not require periodic lubrication. The rotor shaft is mounted on bearings. Each bearing contains a permanent grease supply. Periodically check the mounting bolts for tightness, and the drive belt tension. The drive belt is self-adjusting, within the operating limits of the tensioner. Refer to Drive Belt Tensioner Diagnosis in Engine.
Unit Repair
Service the CS-130D generator as a complete unit.
Removal Procedure
CAUTION: Refer to Battery Disconnect Caution in Service Precautions.
1. Disconnect the negative battery cable.
2. Remove the drive belt.
3. Remove the generator electrical connections.
4. Remove the power steering line clip (3).
5. Remove the generator mounting nuts and bolts.
6. Remove the generator (2).
Installation Procedure
NOTE: Refer to Fastener Notice in Service Precautions.
1. Install the generator (2).
Tighten
^ Tighten the bolts to 50 N.m (37 lb ft).
^ Tighten the nuts to 30 N.m (22 lb ft).
2. Install the generator electrical connections.
3. Install the power steering line clip (3).
4. Install the drive belt.
5. Connect the negative battery cable.
Tighten
Tighten the bolt to 15 N.m (11 lb ft).
The generator does not require periodic lubrication. The rotor shaft is mounted on bearings. Each bearing contains a permanent grease supply. Periodically check the mounting bolts for tightness, and the drive belt tension. The drive belt is self-adjusting, within the operating limits of the tensioner. Refer to Drive Belt Tensioner Diagnosis in Engine.
Unit Repair
Service the CS-130D generator as a complete unit.
Removal Procedure
CAUTION: Refer to Battery Disconnect Caution in Service Precautions.
1. Disconnect the negative battery cable.
2. Remove the drive belt.
3. Remove the generator electrical connections.
4. Remove the power steering line clip (3).
5. Remove the generator mounting nuts and bolts.
6. Remove the generator (2).
Installation Procedure
NOTE: Refer to Fastener Notice in Service Precautions.
1. Install the generator (2).
Tighten
^ Tighten the bolts to 50 N.m (37 lb ft).
^ Tighten the nuts to 30 N.m (22 lb ft).
2. Install the generator electrical connections.
3. Install the power steering line clip (3).
4. Install the drive belt.
5. Connect the negative battery cable.
Tighten
Tighten the bolt to 15 N.m (11 lb ft).
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.