Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2000K TAHOE 4WD V8-5.7L VIN RREPAIR AND DIAGNOSISRESTRAINTS AND SAFETY SYSTEMSAIR BAG SYSTEMSAIR BAGSERVICE AND REPAIRINFLATOR MODULESTEERING WHEEL INFLATOR MODULE
2000 Chevrolet K Tahoe 4WD V8-5.7L VIN R
Steering Wheel Inflator Module
2000 Chevrolet K Tahoe 4WD V8-5.7L VIN RSECTION Steering Wheel Inflator Module
REMOVAL PROCEDURE
CAUTION: Refer to SIR Handling Caution in Service Precautions.
1. Disable the SIR system. Refer to Disabling the SIR System.
2. Turn the ignition switch to the ON position to unlock the steering wheel.
3. Turn the steering wheel 90 degrees so the side of the SIR module is at the 12 o'clock position in order to gain access to the access holes behind the steering wheel.
4. Insert a screwdriver into each access hole and push the leaf spring to release the pin that retains the inflator module.
5. Turn the steering wheel 180 degrees to gain access to the remaining access holes.
6. Insert a screwdriver into each access hole and push the leaf spring to release the pin that retains the inflator module.
7. Tilt the top of the inflator module rearward to gain access to the SIR wiring.
8. Disconnect the SIR lead wire from the clip on the inflator module.
9. Disconnect the SIR lead wire from the clip on the steering wheel.
10. Disconnect the connector position assurance retainer.
11. Disconnect the electrical connector.
CAUTION: When you are carrying an undeployed inflator module:
^ Do not carry the inflator module by the wires or connector on the inflator module
^ Make sure the bag opening points away from you
When you are storing an undeployed inflator module, make sure the bag opening points away from the surface on which the inflator module rests. When you are storing a steering column, do not rest the column with the bag opening facing down and the column vertical. Provide free space for the air bag to expand in case of an accidental deployment. Otherwise, personal injury may result.
12. Remove the inflator module from the vehicle.
INSTALLATION PROCEDURE
CAUTION: When you are carrying an undeployed inflator module:
^ Do not carry the inflator module by the wires or connector on the inflator module
^ Make sure the bag opening points away from you
When you are storing an undeployed inflator module, make sure the bag opening points away from the surface on which the inflator module rests. When you are storing a steering column, do not rest the column with the bag opening facing down and the column vertical. Provide free space for the air bag to expand in case of an accidental deployment. Otherwise, personal injury may result.
IMPORTANT: Verify that the wiring is not exposed or trapped between the inflatable restraint steering wheel module and the steering wheel.
1. Connect the SIR electrical connector.
2. Connect the CPA retainer to the SIR connector.
3. Install the SIR lead wire to the clip on the steering wheel.
4. Install the SIR lead wire to the clip on the inflator module.
5. Press the inflator module into the steering wheel firmly enough that the module engages and latches the notched pins in the leaf springs.
6. Rotate the steering wheel back into the straight position.
7. Enable the SIR system. Refer to Enabling the SIR System.
CAUTION: Refer to SIR Handling Caution in Service Precautions.
1. Disable the SIR system. Refer to Disabling the SIR System.
2. Turn the ignition switch to the ON position to unlock the steering wheel.
3. Turn the steering wheel 90 degrees so the side of the SIR module is at the 12 o'clock position in order to gain access to the access holes behind the steering wheel.
4. Insert a screwdriver into each access hole and push the leaf spring to release the pin that retains the inflator module.
5. Turn the steering wheel 180 degrees to gain access to the remaining access holes.
6. Insert a screwdriver into each access hole and push the leaf spring to release the pin that retains the inflator module.
7. Tilt the top of the inflator module rearward to gain access to the SIR wiring.
8. Disconnect the SIR lead wire from the clip on the inflator module.
9. Disconnect the SIR lead wire from the clip on the steering wheel.
10. Disconnect the connector position assurance retainer.
11. Disconnect the electrical connector.
CAUTION: When you are carrying an undeployed inflator module:
^ Do not carry the inflator module by the wires or connector on the inflator module
^ Make sure the bag opening points away from you
When you are storing an undeployed inflator module, make sure the bag opening points away from the surface on which the inflator module rests. When you are storing a steering column, do not rest the column with the bag opening facing down and the column vertical. Provide free space for the air bag to expand in case of an accidental deployment. Otherwise, personal injury may result.
12. Remove the inflator module from the vehicle.
INSTALLATION PROCEDURE
CAUTION: When you are carrying an undeployed inflator module:
^ Do not carry the inflator module by the wires or connector on the inflator module
^ Make sure the bag opening points away from you
When you are storing an undeployed inflator module, make sure the bag opening points away from the surface on which the inflator module rests. When you are storing a steering column, do not rest the column with the bag opening facing down and the column vertical. Provide free space for the air bag to expand in case of an accidental deployment. Otherwise, personal injury may result.
IMPORTANT: Verify that the wiring is not exposed or trapped between the inflatable restraint steering wheel module and the steering wheel.
1. Connect the SIR electrical connector.
2. Connect the CPA retainer to the SIR connector.
3. Install the SIR lead wire to the clip on the steering wheel.
4. Install the SIR lead wire to the clip on the inflator module.
5. Press the inflator module into the steering wheel firmly enough that the module engages and latches the notched pins in the leaf springs.
6. Rotate the steering wheel back into the straight position.
7. Enable the SIR system. Refer to Enabling the SIR System.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.