Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2000K TAHOE 4WD V8-5.7L VIN RREPAIR AND DIAGNOSISPOWERTRAIN MANAGEMENTCOMPUTERS AND CONTROL SYSTEMSTESTING AND INSPECTIONSCAN TOOL TESTING AND PROCEDURESSCAN TOOL DATA, NORMAL VALUES AND DEFINITIONSSCAN TOOL DATA DEFINITIONS - ANTITHEFT SYSTEMS
2000 Chevrolet K Tahoe 4WD V8-5.7L VIN R
Scan Tool Data Definitions - Antitheft Systems
2000 Chevrolet K Tahoe 4WD V8-5.7L VIN RSECTION Scan Tool Data Definitions - Antitheft Systems
Auto Learn Timer: The scan tool displays the seconds used by the EVO/Passlock (TM) module to learn valid code from the Passlock (TM) sensor. The learn procedure consists of 3 consecutive periods.
Battery Voltage: The scan tool displays the battery system voltage.
Ignition 1: The scan tool displays the state of the ignition switch. The scan tool displays ACTIVE when the ignition switch is in the RUN or CRANK position.
Ignition 3: The scan tool displays the state of the ignition switch. The scan tool displays ACTIVE when the ignition switch is in the RUN position.
Passlock (TM) Code: The scan tool displays the validity of the Passlock (TM) code received by the EVO/Passlock (TM) module. The scan tool displays OPEN, SHORTED, TAMPER and a valid code as a numeric value (1-10).
Passlock (TM) Data Voltage: The scan tool displays the voltage code from the Passlock (TM) sensor to the EVO/Passlock (TM) module. The EVO/Passlock (TM) module determines if the voltage received is a valid or invalid code voltage.
passlock (TM) Power: The scan tool displays the 12v reference voltage at the EVO/Passlock (TM) module. The EVO/Passlock (TM) module determines if the monitored voltage is valid or invalid.
Passlock (TM) State: The scan tool displays the state of the Passlock (TM) system.
Security Lamp Feedback: The scan tool displays the feedback voltage at the EVO/Passlock (TM) module. The EVO/Passlock (TM) module determines if the monitored voltage is valid or invalid.
Security Lamp State: The scan tool displays the state of the SECURITY lamp. The scan tool displays ON, OFF or FLASHING.
Tamper Timer: The scan tool displays the time remaining when in the tamper mode. The timer starts when the ignition switch is turned to the RUN position and the EVO/Passlock (TM) module receives a Passlock (TM) data voltage different from the last learned voltage. The timer has a delay of 10 minutes and will stay active even it the ignition switch is cycled from the RUN to the OFF position.
Battery Voltage: The scan tool displays the battery system voltage.
Ignition 1: The scan tool displays the state of the ignition switch. The scan tool displays ACTIVE when the ignition switch is in the RUN or CRANK position.
Ignition 3: The scan tool displays the state of the ignition switch. The scan tool displays ACTIVE when the ignition switch is in the RUN position.
Passlock (TM) Code: The scan tool displays the validity of the Passlock (TM) code received by the EVO/Passlock (TM) module. The scan tool displays OPEN, SHORTED, TAMPER and a valid code as a numeric value (1-10).
Passlock (TM) Data Voltage: The scan tool displays the voltage code from the Passlock (TM) sensor to the EVO/Passlock (TM) module. The EVO/Passlock (TM) module determines if the voltage received is a valid or invalid code voltage.
passlock (TM) Power: The scan tool displays the 12v reference voltage at the EVO/Passlock (TM) module. The EVO/Passlock (TM) module determines if the monitored voltage is valid or invalid.
Passlock (TM) State: The scan tool displays the state of the Passlock (TM) system.
Security Lamp Feedback: The scan tool displays the feedback voltage at the EVO/Passlock (TM) module. The EVO/Passlock (TM) module determines if the monitored voltage is valid or invalid.
Security Lamp State: The scan tool displays the state of the SECURITY lamp. The scan tool displays ON, OFF or FLASHING.
Tamper Timer: The scan tool displays the time remaining when in the tamper mode. The timer starts when the ignition switch is turned to the RUN position and the EVO/Passlock (TM) module receives a Passlock (TM) data voltage different from the last learned voltage. The timer has a delay of 10 minutes and will stay active even it the ignition switch is cycled from the RUN to the OFF position.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.