Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET1999LUMINA V6-3.8L VIN KREPAIR AND DIAGNOSISPOWERTRAIN MANAGEMENTIGNITION SYSTEMKNOCK SENSORSERVICE AND REPAIR
1999 Chevrolet Lumina V6-3.8L VIN K
Knock Sensor: Service and Repair
1999 Chevrolet Lumina V6-3.8L VIN KSECTION Service and Repair
REMOVAL PROCEDURE
CAUTION:
^ Hot engine coolant may cause severe burns. Although the cooling system has been drained, coolant still remains in the engine water jacket. This coolant will drain with the removal of the knock sensor.
^ Refer to Battery Disconnect Caution in Service Precautions.
1. Disconnect the negative battery cable.
2. Raise the vehicle. Refer to Vehicle Lifting in Service Precautions.
3. Remove the splash shield.
4. Drain the cooling system. Refer to Draining and Filling Cooling System in Engine Cooling.
5. Remove the knock sensor heat shield mounting bolt located under the freeze plug (or block heater if equipped).
6. Disconnect the knock sensor wiring harness connector from the knock sensor.
7. Remove the knock sensor from the engine block.
INSTALLATION PROCEDURE
NOTE: Refer to Fastener Notice in Service Precautions.
IMPORTANT: Do Not apply thread sealant to sensor threads. The sensor is coated at factory and applying additional sealant will affect the sensor's ability to detect detonation.
1. Install the knock sensor into the engine block.
Tighten
Tighten the knock sensor to 19 N.m (14 lb ft).
2. Install the knock sensor heat shield mounting bolt located under the freeze plug (or block heater if equipped).
3. Connect the knock sensor wiring harness connector to the knock sensor.
4. Install the splash shield.
5. Lower the vehicle.
6. Fill the cooling system. Refer to Draining and Filling Cooling System in Cooling System.
CAUTION: Refer to Battery Disconnect Caution in Service Precautions.
7. Reconnect the negative battery cable.
CAUTION:
^ Hot engine coolant may cause severe burns. Although the cooling system has been drained, coolant still remains in the engine water jacket. This coolant will drain with the removal of the knock sensor.
^ Refer to Battery Disconnect Caution in Service Precautions.
1. Disconnect the negative battery cable.
2. Raise the vehicle. Refer to Vehicle Lifting in Service Precautions.
3. Remove the splash shield.
4. Drain the cooling system. Refer to Draining and Filling Cooling System in Engine Cooling.
Knock Sensor:
5. Remove the knock sensor heat shield mounting bolt located under the freeze plug (or block heater if equipped).
6. Disconnect the knock sensor wiring harness connector from the knock sensor.
7. Remove the knock sensor from the engine block.
Knock Sensor:
INSTALLATION PROCEDURE
NOTE: Refer to Fastener Notice in Service Precautions.
IMPORTANT: Do Not apply thread sealant to sensor threads. The sensor is coated at factory and applying additional sealant will affect the sensor's ability to detect detonation.
1. Install the knock sensor into the engine block.
Tighten
Tighten the knock sensor to 19 N.m (14 lb ft).
2. Install the knock sensor heat shield mounting bolt located under the freeze plug (or block heater if equipped).
3. Connect the knock sensor wiring harness connector to the knock sensor.
4. Install the splash shield.
5. Lower the vehicle.
6. Fill the cooling system. Refer to Draining and Filling Cooling System in Cooling System.
CAUTION: Refer to Battery Disconnect Caution in Service Precautions.
7. Reconnect the negative battery cable.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.