Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET1999LUMINA V6-3.8L VIN KREPAIR AND DIAGNOSISMAINTENANCEALIGNMENTSPECIFICATIONSRIDE/TRIM HEIGHT SPECIFICATIONS
1999 Chevrolet Lumina V6-3.8L VIN K
Ride/Trim Height Specifications
1999 Chevrolet Lumina V6-3.8L VIN KSECTION Ride/Trim Height Specifications
Trim Height Specifications
P22560R16 Tire Size
2 Door:
D (Curb) 255 mm (10.04 inch)
J (Curb) 213.3 mm (8.40 inch)
K (Curb) 213.3 mm (8.40 inch)
Z (Curb) 48 mm (1.89 inch)
4 Door:
D (Curb) 255 mm (10.04 inch)
J (Curb) 213.3 mm (8.40 inch)
K (Curb) 213.3 mm (8.40 inch)
Z (Curb) 48 mm (1.89 inch)
P20570R15 Tire Size
4 Door:
D (Curb) 261 mm (10.28 inch)
J (Curb) 213.3 mm (8.40 inch)
K (Curb) 213.3 mm (8.40 inch)
Z (Curb) 55.0 mm (2.13 inch)
D measurement image
- The D height (represented as 1 in the figure) is measured from a point 30 mm outboard of the rear brake hose bracket bolt centerline to the bolt centerline of the trailing arm to the knuckle attachment.
Z measurement image
- The Z height is measured in line with the wheel center:
1 represents the center of the rear bushing bolt
2 represents the lowest inboard point on the ball
J or K measurement image
P22560R16 Tire Size
2 Door:
D (Curb) 255 mm (10.04 inch)
J (Curb) 213.3 mm (8.40 inch)
K (Curb) 213.3 mm (8.40 inch)
Z (Curb) 48 mm (1.89 inch)
4 Door:
D (Curb) 255 mm (10.04 inch)
J (Curb) 213.3 mm (8.40 inch)
K (Curb) 213.3 mm (8.40 inch)
Z (Curb) 48 mm (1.89 inch)
P20570R15 Tire Size
4 Door:
D (Curb) 261 mm (10.28 inch)
J (Curb) 213.3 mm (8.40 inch)
K (Curb) 213.3 mm (8.40 inch)
Z (Curb) 55.0 mm (2.13 inch)
D measurement image
- The D height (represented as 1 in the figure) is measured from a point 30 mm outboard of the rear brake hose bracket bolt centerline to the bolt centerline of the trailing arm to the knuckle attachment.
Z measurement image
- The Z height is measured in line with the wheel center:
1 represents the center of the rear bushing bolt
2 represents the lowest inboard point on the ball
J or K measurement image
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.