Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET1982CELEBRITY L4-151 2.5LREPAIR AND DIAGNOSISBODY AND FRAMETECHNICAL SERVICE BULLETINS
1982 Chevrolet Celebrity L4-151 2.5L
Body and Frame: Technical Service Bulletins
1982 Chevrolet Celebrity L4-151 2.5LSECTION Technical Service Bulletins
- Customer Interest
- Interior - Eliminating Unwanted Odors in Vehicles
- Body - Stain/Film On Windshield Glass Perimeter
- Front Floor Pan - Noise During Acceleration and Braking
- Dash Board - Cleaning of Upper Panel Surfaces
- Door Inside Lock Knob - Falls Off the Door Lock Rod
- Door Locks - Binding or Sticking or Key Hard to Insert
- Rear Compartment Weatherstrip - Ooze-Out
- Rear Compartment Weatherstrip Ooze-Out - Service
- Seats - Recliner Control Cannot Be Adjusted
- Carpet Inserts - Loose
- By Symptom
- Abnormal wear/deterioration
- Customer Interest
- Interior - Eliminating Unwanted Odors in Vehicles
- Body - Stain/Film On Windshield Glass Perimeter
- Front Floor Pan - Noise During Acceleration and Braking
- Dash Board - Cleaning of Upper Panel Surfaces
- Door Inside Lock Knob - Falls Off the Door Lock Rod
- Door Locks - Binding or Sticking or Key Hard to Insert
- Rear Compartment Weatherstrip - Ooze-Out
- Rear Compartment Weatherstrip Ooze-Out - Service
- Seats - Recliner Control Cannot Be Adjusted
- Carpet Inserts - Loose
- Inoperative
- Leaks
- Loose
- Noise
- Odors
- Sticking/Binding
- All Technical Service Bulletins
- Body - Paint-less Dent Repair Process
- Interior - Eliminating Unwanted Odors in Vehicles
- Locks - Key Code Security Rules, Key Code Look Up
- Body - Hem Flange Sealer For Corrosion Protection
- Body - Metal Body Panel Corrosion Protection
- Body - Side Window Chipping Information
- Body - Application of Anti-Corrosion Materials
- Body - Drilling High Strength Steel Using CryoCobalt(R)
- Body - Squeeze Type Resistance Spot Welding/Equipment
- Body - Stain/Film On Windshield Glass Perimeter
- 06-08-111-004B - BULLETIN CANCELLATION NOTIFICATION
- Body - Hem Flange Rust Repair Information
- Body - Metal Panel Adhesive Bonding Information
- Body - Exterior Panel Repairs
- Body - Sealer Tape For Collision Repairs
- Body/Interior - Service Repair Replacement Parts
- Body - Underbody Dimensions Change
- Front Floor Pan - Noise During Acceleration and Braking
- Dash Board - Cleaning of Upper Panel Surfaces
- Door Inside Lock Knob - Falls Off the Door Lock Rod
- Door Locks - Binding or Sticking or Key Hard to Insert
- Lock Cylinders - Inoperative/Proper Lubricant Usage
- Rear Compartment Weatherstrip - Ooze-Out
- Rear Compartment Weatherstrip Ooze-Out - Service
- Sunroof - Vista Vent Hardware Nut
- Striker - I/P Compartment Door Lock
- Rear Compartment Lid - Service Hinge Replacement
- Seats - Recliner Control Cannot Be Adjusted
- Instrument Panel - Paint Repairs
- Key Code - Information
- Paint - Basecoat/Clearcoat Repair Systems
- Paint - High Volume Low Pressure Paint Application
- Warranty - Rail Dust Removal & Chemical Spotting Labor
- Paint - Anti Chip Coatings
- Carpet Inserts - Loose
- Body - Polypropylene Energy Absorber Replacement
- Body - Maintaining Exterior Weatherstrip Appearance
- Interior - Proper Use of Floor Mats
- Interior - Seat Cover Wrinkle/Crease/Burn Info
- Body - Pre-Painting/Cleaning Process For TPO Plastic Fascias
- Interior - Cleaning Instrument Panel, Interior Trim
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.